Operation - EINHELL GE-CT 18 Li Kit Instructions D'origine

5.4 Height adjustment (Fig. 8)
Undo the union nut (Item 5) until the grass trim-
mer handle can be moved in and out freely. Now
set the required working height (Fig. 9) and se-
cure the handle in this position by tightening the
union nut again.
5.5. Fitting the additional handle (Fig. 10)
Fit the additional handle to the mount provided,
paying attention to the teeth (Item I & II). Then
secure the additional handle with the help of the
screw and the adjustment lock provided. Make
sure that the compartment for the spare blades
faces the top of the equipment.
5.6 Adjusting the additional handle (Fig. 11)
Undo the adjustment lock (Item 3) for the additi-
onal handle until it can be moved forwards and
backwards without any great resistance. Set the
required position and tighten the securing screw
again.
5.7 Adjusting the angle of tilt of the guide
handle (Fig. 12)
Press the button for the angle of tilt adjustment
(Item K). Now you can set the long handle to the
required tilt. Release the button and allow the
handle to lock into position to fi x the angle of tilt.
Three diff erent locking angles are possible.
5.8. Installing the battery (Fig. 13/14)
Press the side pushlock buttons of the battery
pack as shown in Fig. 13 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 14, make sure that
the pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.9 Charging the battery (Fig. 15)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(10) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (11) into the battery
charger (10).
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
Anl_GE_CT_18_Li_Kit_2_Ah_SPK9.indb 23 Anl_GE_CT_18_Li_Kit_2_Ah_SPK9.indb 23
GB
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless grass trim-
mer drops. Never fully discharge the battery pack.
This will cause it to develop a defect.
5.10 Battery capacity indicator (Fig. 16)
Press the switch for the battery capacity indicator
(Item C). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

To obtain maximum performance from your grass
trimmer, please follow these instructions:
•
Never use the grass trimmer without the
guard.
•
Do not mow grass when it is wet. The best
results are achieved with dry grass.
•
To switch on your grass trimmer, press the
safety lock-off (Fig. 2 / Item 1) and the On/Off
switch (Fig. 2 / Item 2).
•
To switch off your grass trimmer, let go of the
On/Off switch again (Fig. 2 / Item 2).
•
Do not allow the grass trimmer near the grass
- 23 -
02.04.2019 07:50:23 02.04.2019 07:50:23