Phottix Indra500 TTL Manuel D'utilisation page 9

Wireless Receiving Mode
The Phottix Indra500 TTL Studio Light is equipped with 5 wireless receiving
modes: Odin-C, Odin-N, Strato II, Opt-Slave and RX OFF. Please see below for
more details.
Supported Flash Modes
Odin-C Radio Frequency Receiving Mode
This mode allows the Indra500 TTL Studio Light to be triggered by a Phottix
Odin TTL Flash Trigger TCUs for Canon or by a Phottix Mitros+ TTL Transceiver
Flash for Canon in Odin TX mode. To work correctly they must be set to the same
channel and in the same group.
How to use:
1. Press Function Button 4 or turn the "Adjust/Set Knob" until
pears on the LCD display.
2. Press the corresponding function button to
ing function option will be highlighted on the LCD display.
3. Turn the "Adjust/Set Knob" to change the wireless mode to Odin-C.
4. Press the "Adjust/Set Knob" to confirm the setting.
5. Press the corresponding function button to
from TTL, Manual or Multi.
Odin-N Radio Frequency Receiving Mode
This mode allows the Indra500 TTL Studio Light to be triggered by a Phottix
Odin TTL Flash Trigger TCUs for Nikon or by a Phottix Mitros+ TTL Transceiver
Flash for Nikon in ODIN TX mode. To work correctly they must be set to the same
channel and in the same group.
How to use:
1. Press Function Button 4 or turn the "Adjust/Set Knob" until
pears on the LCD display.
2. Press the corresponding function button to
ing function option will be highlighted on the LCD display.
3. Turn the "Adjust/Set Knob" to change the wireless mode to Odin-N.
4. Press the "Adjust/Set Knob" to confirm the setting.
5. Press the corresponding function button to
from TTL, Manual or Multi.
9
En
Strato II Radio Frequency Receiving Mode
This mode allows the Indra500 TTL Studio Light to be triggered by the Phottix
Odin TTL Flash Trigger TCUs for Canon/Nikon, the Phottix Mitros+ TTL Transceiv-
er Flash for Canon/Nikon in Odin Tx mode, the Phottix Strato TTL transmitter
for Canon/Nikon or by the Phottix Strato II Multi transmitter for Canon/Nikon.
To work correctly they must be set to the same channel and in the same group.
Please note:
HSS, SCS, and TTL are not supported in Strato II Radio Frequency Receiving Mode.
How to use:
1. Press Function Button 4 or turn the "Adjust/Set Knob" until
pears on the LCD display.
2. Press the corresponding function button to
ing function option will be highlighted on the LCD display.
3. Turn the "Adjust/Set Knob" to change the wireless mode to Strato II.
4. Press the "Adjust/Set Knob" to confirm the setting.
5. Press the corresponding function button to
from Manual and Multi.
Opt-Slave Optical Pulse Receiving Mode
In this mode any other studio lights or flashes fired nearby will trigger the In-
dra500 TTL Studio Light.
ap-
Please note:
. The wireless recev-
Pre-flashes from nearby TTL flashes will trigger the Phottix Indra if set in Opt-
Slave mode. Please take care when using this mode that nearby TTL flashes
do not trigger the Phottix Indra before you are ready.
How to use:
in to adjust
1. Press Function Button 4 or turn the "Adjust/Set Knob" until
pears on the LCD display.
2. Press the corresponding function button to
ing function option will be highlighted on the LCD display.
3. Turn the "Adjust/Set Knob" to change the wireless mode to Opt-Slave.
4. Press the "Adjust/Set Knob" to confirm the setting.
RX OFF Mode
In this mode wireless receiving is turned off.
ap-
How to use:
. The wireless recev-
1. Press Function Button 4 or turn the "Adjust/Set Knob" until
pears on the LCD display.
2. Press the corresponding function button to
ing function option will be highlighted on the LCD display.
in to adjust
3. Turn the "Adjust/Set Knob" to change the wireless mode to RX OFF..
4. Press the "Adjust/Set Knob" to confirm the setting.
INSTRUCTION MANUAL
. The wireless recev-
in
. The wireless recev-
. The wireless recev-
ap-
to adjust
ap-
ap-