Bosch Indego M 700 Notice Originale page 26

26 | English
Display
Symbol Meaning
Back button
➊
➋ Confirm button
If the confirm button is pressed whilst mow-
ing, the mower will return to the docking
station
➌ ○ Red LED on: mower error
➍ ○ Green LED on: mower is switched on
Green LED off: The mower is inactive and
your four-digit PIN code is required for ac-
tivation.
Or the mower is shut off, the isolator switch
must be turned on and your four digit PIN
code must be entered to activate the
mower.
Note: during a software update, the green
LED and red LED will be on.
➎ Left/right button
➏ Down/up button
➐ Display with dialog screen
➑ 1 2 3 Garden number (shown when more than
one garden map in the mower memory)
Only with Indego M+ 700:
Network signal present
➒
Network signal absent
The display switches into sleep mode, if no input is made for
10 minutes.
Adding a further Garden/Lawn Area
(see figure K)
To install the Indego to an additional lawn area, please follow
the instructions in the Installation Guide.
Separate garden with separate docking station (see fig-
ure K, right side): The mower can be used on up to three
different gardens. For an additional garden, a separate dock-
ing station (see figure A) and the necessary perimeter wire
and pegs are required. If a schedule or the "Bosch AUTO"
F 016 L81 885 | (23.10.2019)
calendar function or the Bosch "SmartMowing" functional-
ity is set, the grass of the area it is in will be cut, within the
defined time slots.
Switch off the mower when transporting it between the indi-
vidual gardens.
Note: software updates have to be carried out on the mower
in every docking station.
To ensure remembering which docking station belongs to
which garden, it is recommended to label the docking sta-
tions with the garden number and description when storing
them for winter.
Without separate docking station: It is possible to connect
the lawn area by placing the perimeter wire between the two
lawn areas parallel to each other as close as possible (see
figure K, top left). The additional lawn area without docking
station is not recorded in the map memory and the mower
will not use the LogiCut cutting strategy in this lawn area
without the docking station. The maximum recommended
lawn area without a docking station is 50 m
mow until it runs out of battery and will need to be carried
back to the docking station for charging.
Mowing
Do not let children ride the mower.
u
Press the stop button on top of the mower before lift-
u
ing. Always lift the mower by its handle. (see figure F)
Make sure the cutting area is free of small animals such as
hedgehogs or tortoises.
Only with Indego M 700: After successful installation you
can either immediately begin to mow by confirming "Mow
now" on the display, or wait for the next scheduled cutting
period, as programmed by the "Bosch AUTO" Calendar
Function (previous setting required).
A manual mowing schedule can also be set up according to
your specific needs.
Only with Indego M+ 700: After successful installation, you
can begin mowing immediately by confirming "Mow now"
on the display, or on the free Bosch Smart Gardening App by
pressing "mow". You could also set up a programmed
schedule, using the Bosch "SmartMowing" functionality,
which can also plan future cutting sessions based on when it
is forecasted to rain. You could also set up a programmed
schedule in the calendar using the display or the Bosch
Smart Gardening App.
The mower must mow a garden 3 times completely (do 3 full
cuts) to learn the garden. During the learning phase, the
visual result may not be optimal.
Approximate runtimes for complete garden coverage using
LogiCut are listed below. Please note that the runtimes will
vary depending on the lawn complexity and number of ob-
jects within the garden.
2
100 m 4 h
2
500 m 16 h
2
700 m 22 h
2
. The mower will
Bosch Power Tools