Eu Certificate Of Conformity - Gardena CST 3519-X Mode D'emploi

Masquer les pouces Voir aussi pour CST 3519-X:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 30
The undersigned Husqvarna AB, S-561 82, Huskvarna, Sweden, hereby certifies that, when leaving our
factory, the units indicated below are in accordance with the harmonised EU guidelines, EU standards of safety
and product specific standards. This certificate becomes void if the units are modified without our approval.
Description of Unit......................Electric Chainsaw
Type(s) ......................................CST3519-X, CSI4020-X - CS = Chainsaw
Year of CE Marking.................... 2009
EU Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC, 2011/65/EU
Harmonised EN:
EN60745-1, EN60745-2-13, EN50366, EN55014-1, EN61000-3-2, EN61000-3-11
Notified Body that carried out the EC type-examination............... MEEI Kft., 1007
Certificate no. ............................................................................... M3 69240049 (CST 3519-X)
Ulm 18/02/2013
Peter Lameli
Global R & D Director - Hand Held
Keeper of technical documentation
Type
Art. no.
Dry Weight (kg)
Power (kW)
Oil tank volume (cm
Chain pitch (inches)
Chain gauge (mm)
Maximum length of guide bar (mm)
Measured Sound Power L
Guaranteed Sound Power L
Sound pressure Level L
Uncertainty K
Value a
Uncertainty K
Mains-Impedance Z
Cutting Speed (m/s)
1) Working area related emission characteristic Level L
Vibrations Value a
according to EN60745-2-13 given in the table.
h
The declared vibration total value has been measured in accordance with a standard test method and may
be used for comparing one tool with another.
The declared vibration total value may also be used in a preliminary assessment of exposure.
Warning:
The vibration emission during actual use of the power tool can differ from the declared total value depending
on the ways in which the tool is used
Operators should identify safety measures to protect themselves that are based on an estimation of
exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle in addition to the trigger time).
2) The Noise Level L
WA
Conformity Assessment Procedure............ Annex V
EN 61000-3-11 Compliance statement
Depending on the characteristics of the local electricity supply network, use of this product may result in short
voltage drops at the instant of switching on. This may influence other electrical equipment e.g a momentary
dimming of a lamp. If the Mains impedance Zmax of your electricity supply is less than the value shown in the
table (applicable to your model) then these effects will not occur. The value of the network impedance may be
determined by contacting your electricity supply authority.

EU Certificate of Conformity

3
)
pA
(dB(A))
pA
1)
(m/s
2
)
h
(m/s
2
)
ah
Ω)
(
max
values according to 2000/14/EC are given in the table.
Váci út 48/a-b
1132 Budapest
Hungary
M3 69240050 (CST 4020-X)
CST3519-X CSI4020-X
2)
(dB(A))
WA
2)
(dB(A))
WA
1)
(dB(A))
according to EN60745-2-13 given in the table.
pA
ENGLISH - 10
8862
8863
5.6
5.5
1.9
2.0
180
180
3/8
3/8
1.3
1.3
350
400
106
106
108
108
95
95
2.5
2.5
5.9
5.3
1.5
1.5
0.310
0.314
12
15

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Csi 4020-x88628863

Table des Matières