Operation - EINHELL TC-TS 820 Mode D'emploi D'origine

6.4 Replacing the table insert (Fig. 4)
•
Important: Pull out the power plug!
•
Remove the screws (23).
•
Take off the saw blade guard (2) (see 6.3).
•
Lift the worn table insert (6) up and out.
•
Fit the replacement table insert by following
the above in reverse.
6.5 Securing on a substructure
The holes (Z) in the machine frame can be used
to secure the equipment to a fi rm, level substruc-
ture such as a workbench. Suitable fastening ma-
terial (screws, etc.) is available from your dealer.
6.6 Sawdust extraction (Fig. 2)
•
The saw is equipped with an extractor port
(18) for chips.
•
This makes it easy to connect to any extrac-
tor.
•
Never use the equipment without the suction
function.
•
Regularly check and clean the suction chan-
nels.

7. Operation

7.1 Switching On and Off (Fig. 1)
•
The saw can be switched on by pressing the
green pushbutton „I".
•
The red pushbutton „0" has to be pressed to
switch off the saw.
7.2 Parallel stop
7.2.1 Stop height (Fig. 7/8)
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
Use the lower stop height for thin workpieces
and the higher stop height for thick workpie-
ces.
•
To change the stop height, open the locking
grips (12) on the parallel stop (7) and take it
off the table.
•
Turn the parallel stop through 180° so that
end which was facing the front now faces the
rear.
•
Retighten the locking grips.
•
Measure the cutting width between the saw
blade and the parallel stop in addition to the
scale indicator. After every new adjustment,
make a trial cut in order to check the set di-
mensions.
Anl_TC_TS_820_SPK1.indb 21 Anl_TC_TS_820_SPK1.indb 21
GB
7.2.2 Cutting width (Fig. 8)
•
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpi-
eces.
•
Slide the parallel stop (7) to the right or left
side of the saw table (1).
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (b)
engraved on the saw table (1).
•
Tighten the two thumb screws (12) in order to
fix the parallel stop (7).
7.3 Setting the angle (Fig. 9/10)
•
Undo the locking grips (14).
•
Slide the two locking grips (14) to set the bla-
de (4) to the required angle value (see scale
(13)).
•
Retighten the locking grips (14).
8. Operation
After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
After switching on the saw, wait for the blade
to reach its maximum speed of rotation befo-
re commencing with the cut.
Secure long workpieces against falling off
at the end of the cut (e.g. with a roller stand
etc.)
Take extra care when starting the cut.
8.1 Cutting narrow workpieces
(width less than 120 mm) (Fig. 11)
•
Adjust the parallel stop (7) to the width of
workpiece you require.
•
Feed in the workpiece with two hands. Always
use the push stick (3) in the area of the saw
blade (4). (A push stick is supplied with the
saw!)
•
Always push the workpiece through to the
end of the splitter (5).
•
Important! With short workpieces, use the
push stick from the beginning.
8.2 Cutting very narrow workpieces (width
less than 30 mm)
•
Adjust the parallel stop (7) to the width of
workpiece you require.
•
Use the push block to press the workpiece
against the parallel stop (7) and push the
workpiece with the push block through to the
end of the splitter (5).
- 21 -
26.10.15 07:14 26.10.15 07:14