Machine Specifications; Technical Data; Noise Emission; Dust Emission - Jet JWS-34KX Mode D'emploi

4. Machine specifications

4.1 Technical data

No-load spindle speed n
o
1700/3500/6000/8000 rpm
Table size 635 x 600 mm
Table height
Spindle diameter
Clamped height
Spindle travel
Router bit collet size
Table opening diameter
Max. tool diameter
Max. tool height above table
dust port diameter
Dimemsions LxWxH
920x680x1090mm
Weight
Mains 230V ~1/N/PE 50Hz
Output power 1,5 kW (2 HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 2.2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN
1807:1999 and EN 848-1.
(Inspection tolerance 4 dB)
Workpiece pine wood:
W=100mm, L=1000mm, moisture
8,5%
Acoustic power level
(according to EN ISO 3746):
Idling LwA 83,4 dB(A)
Operating LwA 90,2 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA 74,2 dB(A)
Operating LpA 83,6 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
Although there is a correlation
between emission and imission levels,
these do not constitute a basis for
determining the necessity of additional
safety measures.
Workplace conditions which could
influence the noise imission level
include the duration of resonance,
space particulars, other noise sources
etc. For example, the number of
machines and other work being
performed. The permissible workplace
levels can vary from country to
country.
This information is intended to allow
the user to make a better estimation
of the hazards and risks involved.

4.3 Dust emission

830mm
The wood shaper JWS-34KX has been
30mm
dust emission inspected.
70mm
80mm
At an air velocity of 20 m/s on the dust
8 and12mm
port dia 100mm:
160mm
Vacuum pressure
180mm
Volume flow
120mm
The machine meets the present
100mm
workplace dust emission limit of
2 mg/m³.
156 kg
4.4 Content of delivery
30mm spindle assembly
10 A
Collets 8mm and 12mm
Fence assembly
16A
Spacer board for fence
Workpiece hold downs
Push stick
Curved guard assembly
5 A
Mitre gauge
Operating tools
16A
Assembly kit
Operating manual
Spare parts list

5. Transport and start up

5.1 Transport and installation

For transport use a forklift or hand
trolley. Make sure the machine does
not tip or fall off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine can be bolted down if
required.
For packing reasons the machine is
not completely assembled.

5.2 Assembly

If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Mount the handle to the hand wheel.
800 Pa
565 m³/h
5
Mount the shaper guard with the two
screws supplied (D, Fig 1) to the
shaper fence top. To lift the shaper
guard push the handle backwards.
Fig 1

5.3 Mains connection

Mains connection and any extension
cords used must comply with
applicable regulations.
Only use power cords marked
H07RN-F.
The mains connection must have a
16 A surge-proof fuse.
The mains voltage must comply with
the information on the machine
licence plate.
Connections and repairs to the
electrical equipment may only be
carried out by qualified electricians.

5.4 Dust connection

Before initial operation, the machine
must be connected to a dust extractor.
The suction should switch on
automatically when the shaper is
switched on.
The flow rate on the suction port must
be 20m/sec.
Flexible hoses must be of "non-
flammable" quality, and must be
connected to the machine ground
system.

5.5 Starting operation

You can start the machine with the
green on button. The red button on the
main switch stops the machine.
Make sure that the spindle is running
the correct direction (counter-
clockwise).