Machine Specifications; Technical Data; Noise Emission; Dust Emission - Jet JPT-310HH Mode D'emploi

Be sure to wear personal protection
gear such as safety goggles and ear
protection. Use a suitable dust
exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

JPT-310HH:
Planing
Jointing width
Table length
Height above floor
Fence size 1100 x 150mm
Fence tilt
Depth of cut
Thicknessing
Thicknessing width
Thicknessing height
Thicknessing table length
Min. length of work piece
Feed speed 3.5 m/min(230V)
Feed speed 7 m/min(400V)
Depth of cut
Number of knives 56 carbide inserts
Cutter block diameter
No load speed n
o
Dust port diameter
Overall (LxWxH) 1400x750x1000mm
Net Weight
Mains 230V ~1/N/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F)
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F)
Installation fuse protection
JPT-410HH:
Planing
Jointing width
Table length
Height above floor
Fence size 1100 x 150mm
Fence tilt
Depth of cut
Thicknessing
Thicknessing width
Thicknessing height
Thicknessing table length
Min. length of work piece
Feed speed 7 m/min(400V)
Depth of cut
Number of knives
Cutter block diameter
No load speed n
Dust port diameter
Overall (LxWxH)
Net Weight
Mains
Output power
Reference current
Extension cord (H07RN-F)
Installation fuse protection
Mains
Output power
Reference current
max 307 mm
Extension cord (H07RN-F)
1400mm
Installation fuse protection
850mm

4.2 Noise emission

0 - 45°
Determined according to EN 861
max.3 mm
(Inspection tolerance 4 dB)
Work piece pine wood:
max 307 mm
W=100mm, L=1000mm, moisture 8,5%
4 - 225 mm
Planing:
540mm
Acoustic power level
150mm
(according to EN ISO 3746):
Idling
Operating
max. 4,5 mm
Acoustic pressure level
(according to EN ISO 11202):
72 mm
Idling
5500 rpm
Operating
100mm
Thicknessing:
Acoustic power level
230 kg
(according to EN ISO 3746):
Idling
Operating
12.5 A
Acoustic pressure level
3x1,5mm²
(according to EN 11202):
16A
Operating position 1:
Idling
Operating
5 A
Operating position 2:
4x1,5mm²
Idling
16A
Operating
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
max 407 mm
Although there is a correlation
1660mm
between emission and imission levels,
850mm
these do not constitute a basis for
determining the necessity of additional
0 - 45°
safety measures.
max.3 mm
Workplace conditions which could
influence the noise imission level
max 407 mm
include the duration of resonance,
4 - 225 mm
spatial particulars, other noise sources
600mm
etc. For example, the number of
150mm
machines and other work being
performed. The permissible workplace
max. 4,5 mm
72 carbide inserts
72 mm
5500 rpm
o
120mm
1660x870x1000mm
315 kg
230V ~1/N/PE 50Hz
2,2 kW (3 HP) S1
13 A
3x1,5mm²
16A
400V ~3/PE 50Hz
3 kW (4 HP) S1
6,5 A
4x1,5mm²
16A
LwA 81,7 dB(A)
LwA 94,3 dB(A)
LpA 72,1 dB(A)
LpA 85,9 dB(A)
LwA 80,7 dB(A)
LwA 87,8 dB(A)
LpA 69,2 dB(A)
LpA 85,7 dB(A)
LpA 70,0 dB(A)
LpA 89,5 dB(A)
levels can vary from country to
country.
This information is intended to allow
the user to make a better estimation of
the hazards and risks involved.

4.3 Dust emission

The planer thicknesser has been dust
emission inspected.
JPT-310HH:
At an air velocity of 20 m/s on the dust
port dia 100mm:
Vacuum pressure
Volume flow
JPT-410HH:
At an air velocity of 20 m/s on the dust
port dia 120mm:
Vacuum pressure
Volume flow
The machine meets a workplace dust
emission limit of 2 mg/m³.
4.4 Content of delivery
Planer thicknesser assembly
Jointer fence assembly.
Cutter block guard
5 spare carbide inserts
10 spare Torx-screws
2 Torx screw drivers
Operating manual
Spare parts list

4.5 Machine description

Fig 1
A....Outfeed table
B....Jointer fence
C....ON/OFF switch, E-stop button
D....Cutterblock guard
E.....Table tilt handle
F....Table adjustment lock
G....Table adjustment handle
H....Infeed table
I.....Table-cabinet lock
J.....Mains plug
900 Pa
565 m³/h
950 Pa
810 m³/h