Before First Use; Operation - Scheppach MP132-40 Traduction Du Manuel D'origine

Information concerning noise emission measured
according to relevant standards:
Sound pressure L = 79,7 dB(A)
pA
Uncertainty K = 3 dB(A)
PA
Sound power L = 90,9 dB(A)
WA
Uncertainty K = 1,83 dB(A)
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration A (left/right) = 8,125 m/s
hv
Uncertainty K = 1,5 m/s
2
PA

7. Before first use

Before starting the equipment
Assembling the components
Some parts of the mower come disassembled.
For quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional tools
(not supplied) for assembly, and also for mainte-
nance work:
• A 1 liter measuring jug (oil/petrol resistant)
• A petrol can (5 liters is sufficient for approx. 6
operating hours)
• A funnel (suitable for the tankʼs petrol filler neck)
• Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
• A petrol suction pump (plastic, available from DIY
stores)
• An oil can with hand pump (available from DIY
stores)
• Spark plug wrench
• 0,4 liter of engine oil (SAE 30/ 10W30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present
2. Insert the bottom push bar (4a) in the hole in the
lawnmower and secure it with 2 screws (d).
3. Attach the upper push bar (4) on the lower push
bar (4a) with one screw (a), one washer (b) and
one star grip nut (5) each on both sides (Fig. 4-5).
4. Insert the pull start handle (17) in the designated
hook as shown in Fig. 6.
5. Fix the cables to the push bar with the cable clips
(18) provided (Fig. 7).
6. Grass box (16) - open it up and click the plastic
clips into position on the frame (Fig. 8).
7. Mowing with grass box:
Lift the discharge flap (15) with one hand and
hang the grass box (16) as shown in Fig. 9.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2
Setting the cutting height
m CAUTION!
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged.
• To prevent any imbalance, replace blunt and/or
damaged blades as a set only (if applicable). To
carry out this check, first switch off the engine and
pull the spark plug boot.
• locate the two front wheels as well as the two re-
ar wheels into the desired cutting height (30-48-
66 mm) position. (L = left-hand thread, R = right-
hand thread)
• ! ensure that the four wheels are fixed in the sa-
me cutting height position (Fig. 13)

8. Operation

m CAUTION!
The engine does not come with oil in it. There-
fore, ensure that you add 0,4 liters of oil before
starting it up. Use normal, multigrade oil (SAE30).
The oil level in the engine must be checked each
time before mowing.
You will also need to fill in petrol, as this is also
not supplied upon delivery.
• In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 1/ Item 3) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
position, at which point the engine automatically
switches off.
• Press the engine brake lever (3) together and give
the starter cord (17) a vigorous pull. (Fig. 14)
Attention:
When you pull the starting rope the cutting blade
rotates even when dissolved motor brake lever.
Make sure that there are no body parts in danger
zone of cutting blade.
• Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
m WARNING
Whenever you need to perform any kind of ad-
justment and/or repair work on your lawn mower,
wait until the blade has come to a complete stop.
Always switch off the engine before carrying out
any adjustments, maintenance or repairs.