CDVI DIGIWAY PLUS DWP 102 Série Manuel D'installation page 23

INSTALLATION MANUAL
DIGIWAY PLUS
The range of motors for the double door is described in the following table: The range of motors for the double door is described in the following table:
Double door total width
1600 mm 1600 mm
1700 mm 1700 mm
1800 mm 1800 mm
1900 mm 1900 mm
2000 mm 2000 mm
With the motors DWPD, with central profi le, the product comes already equipped with synchronization cable. With the motors DWPD, with central profi le, the product comes already equipped with synchronization cable.
It is also possible to use 2 single door units ( DWP102x) to automate a double leaf door with synchronization of each leaf. It is also possible to use 2 single door units ( DWP102x) to automate a double leaf door with synchronization of each leaf.
For that use the serial cable DWPCS For that use the serial cable
The cable is terminated with 2 special 3-way connectors and must be inserted in the corresponding slot located under the logic card of the The cable is terminated with 2 special 3-way connectors and must be inserted in the corresponding slot located under the logic card of the
unit ( see image below ). unit ( see image below ).
1 ) Connect the motors referring to the electrical diagram of the single door. 1 ) Connect the motors referring to the electrical diagram of the single door.
WARNING: in the double door mode, with leaves overlapping (rebated), it is very important to identify the type of unit WARNING: in the double door mode, with leaves overlapping (rebated), it is very important to identify the type of unit
• • MASTER unit drives MASTER unit drives the leaf which opens fi rst and closes last the leaf which opens fi rst and closes last
• • SLAVE SLAVE unit drives unit drives the leaf which opens last and closes fi rst the leaf which opens last and closes fi rst
2 ) Connect the RADARs, the Day/Night switch to the unit identifi ed as MASTER 2 ) Connect the RADARs, the Day/Night switch to the unit identifi ed as MASTER
3 ) The contacts NC of the safety devices ( photocells ) can be connected in 2 ways: 3 ) The contacts NC of the safety devices ( photocells ) can be connected in 2 ways:
• • Connect the photocells contacts to the terminals 5,6,7 of the corresponding unit electronic card Connect the photocells contacts to the terminals 5,6,7 of the corresponding unit electronic card
• • Put in serial the contacts of all the photocells, connect them to the terminals 5,6,7 of the MASTER unit and make a bridge to the Put in serial the contacts of all the photocells, connect them to the terminals 5,6,7 of the MASTER unit and make a bridge to the
contacts 5,6,7 of the SLAVE unit. contacts 5,6,7 of the SLAVE unit.
4 ) Connect the electrolock to the MASTER unit 4 ) Connect the electrolock to the MASTER unit
5 ) On the SLAVE unit memorize 5 ) On the SLAVE unit memorize only
navigation transmitter and any other transmitter used to open the door navigation transmitter and any other transmitter used to open the door
ATTENTION : Do not memorize the same 4ch navigation transmitter on both the units! ATTENTION : Do not memorize the same 4ch navigation transmitter on both the units!
Part II: Electrical connections Part II: Electrical connections
Leaves width
70 - 80 mm 70 - 80 mm
81 - 85 mm 81 - 85 mm
86 - 90 mm 86 - 90 mm
91 - 95 mm 91 - 95 mm
96 - 100 mm 96 - 100 mm
DWPCS ( optional ). ( optional ).
Slave Slave
only the 4ch remote control needed to navigate in the SLAVE unit menu, on the Master unit memorize the the 4ch remote control needed to navigate in the SLAVE unit menu, on the Master unit memorize the
p/n Articulated Arm
DWPD10216ACD DWPD10216ACD
DWPD10217ACD DWPD10217ACD
DWPD10218ACD DWPD10218ACD
DWPD10219ACD DWPD10219ACD
DWPD10220ACD DWPD10220ACD
3 3
Serial cable DWPCS Serial cable DWPCS
Master Master
p/N Sliding Arm
DWPD10216SCD DWPD10216SCD
DWPD10217SCD DWPD10217SCD
DWPD10218SCD DWPD10218SCD
DWPD10219SCD DWPD10219SCD
DWPD10220SCD DWPD10220SCD
cdvigroup.com
EN
cdvi.com
23