CDVI DIGIWAY PLUS DWP 102 Série Manuel D'installation page 18

INSTALLATION MANUAL
DIGIWAY PLUS
Advanced Setting
6) 6)
Dynamic Pause
Advanced Setting
7) 7)
FTC-S Exclusion
FTC-S active zone FTC-S active zone
wall wall
Advanced Setting
8) 8)
Ex Power Open
Advanced Setting
9) 9)
Ex Open Torque
Advanced Setting
10) 10)
Extra Open Time
Advanced Setting
11) 11)
Ex Power Close
Advanced Setting
12) 12)
Ex Close Torque
Advanced Setting
13) 13)
Extra Close Time
Advanced Setting
14) 14)
Fire Release
Advanced Setting
15) 15)
Max Obst Cycles
cdvi.com
18
cdvigroup.com
STEP V: ADVANCED SETTINGS (Continued...) STEP V: ADVANCED SETTINGS (Continued...)
Enable / Disable
FTC-S Exclusion
000
|||||||||||||||||......................
door door
Enable / Disable
Ex Open Torque
50 %
|||||||||||||||||......................
Extra Open Time
0 SEC.
|||||||||||||||||......................
Enable / Disable
Ex Close Torque
50 %
|||||||||||||||||......................
Extra Close Time
0 SEC.
|||||||||||||||||......................
Fire Release
Open/Free/Closed
Max Obst Cycles
000
|||||||||||||||||......................
The dynamic pause is a function which automatically adjusts the pause time The dynamic pause is a function which automatically adjusts the pause time
programmed, avoiding too many closing attempts of the door in high traffi c situations. programmed, avoiding too many closing attempts of the door in high traffi c situations.
When enabled, this function increases by 1 sec. the pause time programmed each time When enabled, this function increases by 1 sec. the pause time programmed each time
it detects a passage through the door during the closing phase, and restarts the time it detects a passage through the door during the closing phase, and restarts the time
when the passage is detected against when the door is open. when the passage is detected against when the door is open.
Once the door completes its cycle up to the closed status, the pause time is reset to the Once the door completes its cycle up to the closed status, the pause time is reset to the
programmed value. programmed value.
Press UP or DOWN buttons to enable or disable the function and confi rm with OK Press UP or DOWN buttons to enable or disable the function and confi rm with OK
Default value = DISABLE. Default value = DISABLE.
If the door is next to a wall and is using a curtain protection device, it may be necessary If the door is next to a wall and is using a curtain protection device, it may be necessary
to prevent the device being activated by the wall to allow a complete opening of the leaf. to prevent the device being activated by the wall to allow a complete opening of the leaf.
Set the zone width as percentage of the full door motion using the UP or DOWN buttons Set the zone width as percentage of the full door motion using the UP or DOWN buttons
to increase or decrease the value. to increase or decrease the value.
000 = Door OPEN 000 = Door OPEN
100 = Door CLOSED 100 = Door CLOSED
Example: if you want to disable the curtain device when the leaf is open at the 80% of Example : if you want to disable the curtain device when the leaf is open at the 80% of
the complete travel, set the value to 20. the complete travel, set the value to 20.
WARNING: the excluded zone may become a health & safety hazard WARNING: the excluded zone may become a health & safety hazard
because it not protected! because it not protected!
When enabled, adds one more When enabled, adds one more OPENING OPENING pulse after the regular
compensate possible friction or door unbalance. compensate possible friction or door unbalance.
Enable or disable this function with the UP or DOWN buttons and confi rm with OK Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Default value = DISABLE Default value = DISABLE
This function allows to set the TORQUE This function allows to set the TORQUE of the
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 50% Default value = 50%
This function allows to set the duration TIME This function allows to set the duration
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 0 SEC. Default value = 0 SEC.
When enabled, adds one more CLOSING When enabled, adds one more CLOSING pulse after the regular
compensate possible friction or door unbalance. compensate possible friction or door unbalance.
Enable or disable this function with the UP or DOWN buttons and confi rm with OK Enable or disable this function with the UP or DOWN buttons and confi rm with OK
Default value = DISABLE Default value = DISABLE
This function allows to set the TORQUE This function allows to set the TORQUE of the
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 50% Default value = 50%
This function allows to set the duration TIME This function allows to set the duration
Change the value by pressing the UP or DOWN buttons and confi rm with OK. Change the value by pressing the UP or DOWN buttons and confi rm with OK.
Default value = 0 SEC. Default value = 0 SEC.
When the Fire Release function is enabled, it's possible to set the reaction of the door When the Fire Release function is enabled, it's possible to set the reaction of the door
depending on the failure of the Fire power ( V+, V-) : depending on the failure of the Fire power ( V+, V-) :
• • DOOR FREE DOOR FREE = In case of = In case of Fire Power Fire Power failure the door becomes FREE
• • DOOR OPEN = In case of DOOR OPEN = In case of Fire Power
the fi re power is reset or the function of the the fi re power is reset or the function of the Menu Confi guration
• • DOOR CLOSED LOCKED DOOR CLOSED LOCKED = Door CLOSED and lock active
• • DOOR CLOSED UNLOCKED DOOR CLOSED UNLOCKED = = Door CLOSED and lock disactive
When the door meets an obstacle during closing, it re-opens immediately. At the end of When the door meets an obstacle during closing, it re-opens immediately. At the end of
the pause time, it re-closes slowly. If the obstacle is still present the cycle restarts. the pause time, it re-closes slowly. If the obstacle is still present the cycle restarts.
It is possible to set the max number of re-closing attempts by the door before stopping to It is possible to set the max number of re-closing attempts by the door before stopping to
await a defi nitive command. Change this parameter (from 1 1 to to 256) await a defi nitive command. Change this parameter (from
or DOWN or DOWN buttons and confi rm with OK. buttons and confi rm with OK.
Default value = 4 attempts. Default value = 4 attempts.
pulse after the regular OPENING
of the OPENING OPENING extra pulse extra pulse
TIME of the of the OPENING OPENING extra pulse extra pulse
pulse after the regular CLOSING
of the CLOSING CLOSING extra pulse extra pulse
TIME of the of the CLOSING CLOSING extra pulse extra pulse
failure the door becomes FREE
Fire Power failure the door opens and stays OPEN until failure the door opens and stays OPEN until
Menu Confi guration is disabled.
= Door CLOSED and lock active
Door CLOSED and lock disactive
256) by pressing the
EN
OPENING cycle to cycle to
CLOSING cycle to cycle to
is disabled.
by pressing the UP UP