Spare Parts; Scope Of Supply; Delivery Form; Troubleshooting - Kulzer Dynamix Speed Mode D'emploi

66

Spare Parts

Please refer to the enclosed spare parts list for the order numbers of spare parts.
Please state the item number and serial number of the unit in addition to the desired order number when ordering spare parts.
Serial number and date of manufacturing are shown on the type plate of the unit.
Accessories and Spare Parts
66033825 DYNAMIX WALL MOUNT (wall mount)
66034326 DYNAMIX UK POWER CORD 230 V (mains cable United Kingdom)
66034327 DYNAMIX CH POWER CORD 230 V (mains cable Switzerland)
66034592 DYNAMIX EU POWER CORD 230 V (mains cable EU)
66041021 DYNAMIX SPARE PART COVER NEW (NEW FORM) (spare part – unit cover new shape)
66032128 DYNAMIX SPARE PART PLUNGER DISC (spare part – plungers' disc)
66034329 DYNAMIX SPARE PART FUSE EU 230 V (spare part – fuse 230 V)
66047093 DYNAMIX SPARE PART BASE PLATE NEW (NEW COLOR) (spare part – unit plate new color)
66035030 DYNAMIX SPARE PART BASE FEET 4pcs (spare part – unit feet 4pcs)
66035051 DYNAMIX SPARE PART RUBBER STAMP (spare part – catch)
7

Scope of Supply

1 Dynamix speed Mixing unit
1 Power cord
1 Instructions for use
8

Delivery Form

Item no.: 66045779 – Dynamix speed EU Standard; 230 V, 50 Hz
66045802 – Dynamix speed US; 120 V, 60 Hz
66046459 – Dynamix speed JP; 100 V, 50/60 Hz
9

Troubleshooting

Error
LEDs do not light LED (5, 6, 7,
fig 1), plungers will not move
The unit does not
switch on
Plungers will not move,
"Unit cover" LED (7, fig 1)
is on or flashes
The plungers move slowly
toward the cartridge
Cartridges cannot be removed /
cannot be installed
The hexagonal end
(13, fig1) fails to turn
Unit automatically reduces the
extrusion speed
The mixing nozzle (21, fig1)
bursts
The tubular bag bursts or is
damaged
Cause
• The unit is not switched on.
• Power cord not properly connected to the
unit.
• Fuse blown.
• No power at the wall outlet.
• Unit fault.
• Unit cover not properly closed.
• The cover was opened before the plun-
gers had stopped. A previous cartridge
position has been saved.
• Plungers' disc have not fully retracted to
their home position.
• The mixer shaft has not threaded itself.
• Material has hardened in the mixing nozzle.
• The mixer motor's thermal protector
has activated.
• Unit detects a highly viscous or
too cold impression material (below
21°C [70°F]) and automatically reduces
the extrusion speed and mixer rotary
speed.
• Contamination (e.g. debris) in the
cartridge holder.
• Insufficient spindle lubrication.
• Incorrect mixing nozzle installed.
• Mixing tip / foil bag not compatible.
• Plungers' disc are too much worn or have
been damaged, causing the tubular bag
to be pinched between the plungers' disc
and the cartridge.
• The material has partially hardened in the
cartridge.
Item no.:
Corrective action
• Switch the unit on at the main power switch
(17, fig. 1).
• Check that the unit plug is properly seated (fig. 2).
• Replace the fuse (refer to Sec. 6.5).
• Check that there is power at the wall outlet.
• Return the unit for repair.
• Close the unit cover (8, fig. 1) and check that the
cartridges are properly seated. If required, seat
cartridges correctly.
• Press retract key (4, fig 1) and wait until the plungers
have reached their home position and have stopped.
Then repeat the process with the cartridge.
• Press the retract key (4, fig 1) and allow the plungers
to retract until they stop automatically. They are now
in their home position (refer to Sec. 5.1).
• Check that the cartridge is properly seated.
• Install a new nozzle.
• Allow the unit to cool down for approx. 30 minutes.
Observe the maximum permissible operating time
(2 minutes of operation, 5 minute pause).
• This only occurs if the impression material is highly
viscose or too cold. Refer to the manufacturer's
processing instructions (processing temperature)
or handle the impression material with a room
temperature between 21 – 25°C [70 – 77°F].
• Clean the inner surfaces of the cartridge holder and
plungers' disc.
• Lubricate the spindles.
• Use the mixing nozzle specified by the manufacturer.
• Contact the manufacturer of the mixing tip / foil bag.
• Replace the plungers' disc (refer to Sec. 6.3).
• Replace the cartridge (refer to Sec. 5.1).
66045779
GB
- 9 -