Scope Of Delivery; Accessories; Pump Handling; Facility Requirements - Lowara ecocirc XL Manuel D'installation, D'utilisation Et D'entretien

en - Translation of the original instructions
Feature Description
Motor model Electronically commutated motor
with permanent magnet rotor
Series ecocirc XL
ecocirc XLplus
Rated voltage 1 x 230 V ±10%
Frequency 50/60 Hz
Power con- 40÷1700 W
sumption
IP protection IP 44
Insulation Class 155 (F)
class
Maximum The maximum pressure is indicat-
working pres- ed on pump data plate
sure
0.60 MPa (6 bar)
1.0 MPa (10 bar)
Permitted liq- The maximum temperature is indi-
uid tempera- cated on pump data plate
ture
from -10°C (14°F) to +110°C
(230°F) for heating pumps
from -10°C (14°F) to +85°C (185°F)
for domestic hot water pumps
Permitted from 0°C (32°F) to 40°C (104°F)
ambient tem-
perature
Permitted < 95%
ambient hu-
midity
Permitted Heating water according to VDI
pumping me- 2035, water/glycol mixtures
dia 50%.
Sound pres- ≤ 43 dB (A)
sure
EMC (electro- EN 55014-1:2006 + A1:2009 +
magnetic A2:2011, EN 55014-2:1997 +
compatibility) A1:2001 + A2:2008, EN
61000-3-2:2006 + A1:2009 +
A2:2009, EN 61000-3-3:2008,
61800-3:2004+A1:2012.
Leakage cur- < 3.5 mA
rent
I/O auxiliar Imax < 40 mA
+15 VDC
power supply
(Not available
on 25-40,
25-60, 32-40,
32-60 mod-
els)
Fault signal Vmax < 250 VAC
relay
Imax < 2 A

3.4 Scope of delivery

10
Performance of the pump is referred to water at 25°C (77°F). Pumped media with different viscosity will have impact
on such performances.
18
Inside the package you will find:
• Pump unit
• Insulating shells (single head only)
• Gasket (OR) to be used as replacement for the
OR mounted between motor and pump hous-
ing
• Plug connector (for 25-40, 25-60, 32-40, 32-60
models only)
• Seal for threaded connection (only for threaded
pump housing)
• Seal for flanged connection (only for flanged
pump housing)
• Eight M12 washers and eight M16 washers (for
models from DN32 to DN65)
• Eight M16 washers (for DN80 and DN100 PN6
model)
• Sixteen M16 washers (for DN80 and DN100
PN10 models)

3.5 Accessories

• Counter flanges
• Blind flanges
• Port to port adapters
• Pressure sensor (for details see section 5.2.9 of
this manual)
• Temperature probe (for details see section
5.2.9 of this manual)
• RS485 module (only for ecocirc XLplus)
• Wireless module (only for ecocirc XLplus)
4 Installation
Precautions
10
up to

4.1 Pump handling

Always lift the pump by the pump head or pump
housing. If the pump weight exceeds the manual
handling limits, use lifting equipment, positioning
lifting straps according to

4.2 Facility requirements

4.2.1 Pump location

WARNING:
• Observe accident prevention regu-
lations in force.
• Use suitable equipment and protec-
tion.
• Always refer to the local and/or na-
tional regulations, legislation, and
codes in force regarding the selec-
tion of the installation site, plumb-
ing, and power connections.
WARNING:
Observe local regulations setting the
limits for manual lifting or handling.
Figure 11
DANGER:
Do not use this unit in environments
that may contain flammable/explosive
or chemically aggressive gases or pow-
ders.
.