Maintenance And Service; Maintenance And Cleaning - Bosch PMF 180 E Multi Instructions D'emploi

OBJ_BUCH-345-003.book Page 17 Monday, May 14, 2007 4:11 PM
Sanding
The removal rate and the sanding pattern are primarily
determined by the choice of sanding sheet, the preset
oscillation rate and the applied pressure.
Only flawless sanding sheets achieve good sanding
capacity and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an
increase of the sanding capacity, but to increased wear
of the machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and
hard to reach areas, it is also possible to work only with
the tip or an edge of the sanding plate.
A sanding sheet that has been used for metal should
not be used for other materials.
Use only original Bosch sanding accessories.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep the
machine and ventilation slots clean.
Clean the HM-Riff segment saw blade (accessory) reg-
ularly with a wire brush.
WARNING! Important instructions for connecting
a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to the fol-
lowing code:
Do not connect the blue or brown wire to the earth ter-
minal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it must be
disposed of safely.
If the machine should fail despite the care taken in man-
ufacturing and testing procedures, repair should be
carried out by an after-sales service centre for Bosch
power tools.
In all correspondence and spare parts order, please
always include the 10-digit article number given on the
type plate of the machine.
2 609 000 229 • 14.5.07
Service and Customer Assistance
Exploded views and information on spare parts can be
found under:
www.bosch-pt.com
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service:. . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 82
✆ Advice line:. . . . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax: . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 89
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
✆ Service:. . . . . . . . . . . . . . . . .+353 (0)1 / 4 66 67 00
Fax: . . . . . . . . . . . . . . . . . . . . . .+353 (0)1 / 4 66 68 88
Australia and New Zealand
Robert Bosch Australia Pty. Ltd.
RBAU/SPT
1555 Centre Road
P.O. Box 66
3168 Clayton/Victoria
✆ . . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 44
Fax: . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 45
www.bosch.com.au
Disposal
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According the European Guideline
2002/96/EC for Waste Electrical and
Electronic Equipment and its implemen-
tation into national right, power tools
that are no longer usable must be collected separately
and disposed of in an environmentally correct manner.
Subject to change without notice.
English | 17