Table des Matières
Publicité
Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the
colours alternating from 01 to 99. Confirm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". The cursor will appear
in the bottom line at the same time and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the strobe frequency
from 01 to 99 (FLASH:00 = strobe deactivated, FLASH:01 = approx. 1 Hz, FLASH:99 = approx. 20 Hz). Confirm with ENTER.
JUMPING
JUMPING
JUMPING
SPEED:99
COLOUR FADING (FADING)
In the colour fading mode (fading mode) different colours are blended into one another in succession. The speed of the program is adjustable
separately and a stroboscope effect can also be activated. Press the MODE button repeatedly until "FADING" appears in the upper line of the display.
Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the
colours alternating from 01 to 99. Confirm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". The cursor will appear
in the bottom line at the same time and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the strobe frequency
from 01 to 99 (FLASH:00 = strobe deactivated, FLASH:01 = approx. 1 Hz, FLASH:99 = approx. 20 Hz). Confirm with ENTER.
FADING
FADING
FADING
SPEED:99
AUTOMATIC CONTROL MODE (AUTO)
In this operating mode, the light switches automatically between colour change and colour blending mode. The speed of the program is adjustable
separately and a stroboscope effect can also be activated. Press the MODE button repeatedly until "AUTO" appears in the upper line of the display.
Now, press ENTER until the cursor appears in the lower line of the display, and then select the speed (SPEED) using the UP and DOWN buttons from
01 to 99. Confirm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". The cursor will appear in the bottom line at the
same time and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the strobe frequency from 01 to 99 (FLASH:00 =
strobe deactivated, FLASH:01 = approx. 1 Hz, FLASH:99 = approx. 20 Hz). Confirm with ENTER.
01 AUTO
AUTO
02 AUTO
SPEED:99
SLAVE-MODE (SLAVE MODE)
Press the MODE button repeatedly until "SLAVE MODE" appears on the display. Connect the DMX IN of the slave to the DMX OUT of the master unit
(same model). Now the slave unit follows the master unit.
SLAVE
M O D E
MUSIC CONTROL MODE (SOUND MODE)
Press the MODE button repeatedly until "SOUND" appears on the display. Now the spotlight is controlled by the built-in microphone and follows the
beat of the music (bass pulses). To adjust the microphone sensitivity, press ENTER, and the cursor appears in the lower line of the display "SENS:xx"
and use the UP and DOWN buttons to set the desired value (SENS:00 = minimum sensitivity, SENS:99 = maximum sensitivity). Confirm the input with
ENTER.
SOUND
SENS:99
DIMMER RESPONSE (DIMMER RESPON)
The menu item DIMMER RESPONSE offers two possibilities of how the spotlight responds to the DMX value changes. DIMMER RESPON01: The
light reacts abruptly to changes in the DMX value. DIMMER RESPON02: The light behaves in a manner similar to that of a halogen lamp with gentle
changes in brightness. Press the MODE button repeatedly until "DIMMER RESPON" appears on the display. Press ENTER, and the cursor appears in
the lower line of the display and then use the UP and DOWN buttons to select the desired setting. Confirm the input with ENTER.
DIMMER
RESPON01
SELECTING THE DMX MODE (DMX CH MODE)
Press the MODE button repeatedly until "DMX MODE" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line
of the display and then use the UP and DOWN buttons to select one of the six DMX modes (02CH, 03CH1, 03CH2, 04CH, 09CH, 10CH). Confirm with
ENTER. You will find tables with the channels of the different DMX modes on the following pages of this manual.
DMX MODE
10CH
DMX STARTING ADDRESS (DMX ADDR)
Press the MODE button repeatedly until "DMX ADDR" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line
of the display and then use the UP and DOWN buttons to select the desired DMX start address between 001 and 512. Confirm with ENTER.
DMX ADDR
001
16
SPEED:01 - 99
FLASH:00 - 99
SPEED:01 - 99
FLASH:00 - 99
SPEED:01 - 99
FLASH:00 - 99
Publicité
Table des Matières
