Start-Up; Cleaning And Care Instructions; Disposal; Processing In Case Of Guarantee Claim - Parkside 351637-20-A Mode D'emploi

GB/IE
do not use the product. Contact the
manufacturer at the indicated ser-
vice address.

6.2 Start-up

Connect the tap
1. Turn the tap closed.
2. Make sure that the hose connector
valve 5 is set to (2 "OFF") position
and is at a right angle to the product,
see Fig. B-(A).
Attachment to the water connec-
tion with (DN 15) 21 mm (G ½")
- outer thread Fig. A-(A)
1. Screw the tap connector 2 onto the
tap.
2. Screw the hose connector valve
adapter 3 onto the tap connector
2 .
3. Push the hose connector valve
4 onto the hose connector valve
adapter 3 until it clicks in.
4. Check the tightness.
Attachment to the water connec-
tion with (DN 20) 26.5 mm (G
¾") - outer thread Fig. A-(B)
1. Screw the hose connector valve
adapter 3 onto the tap.
2. Push the hose connector valve
4 onto the hose connector valve
adapter 3 until it clicks in.
3. Check the tightness.
Operation
NOTE!
Convince yourself before the first
use of the tight fit of all connec-
tions. If necessary, tighten it a
little.
1. Unroll the product 1 completely be-
fore use.
2. Turn on the tap only a little at first
and increase the water pressure
14
evenly. The product will roll out.
3. Once the product is completely un-
rolled, open the valve on the hose
connector valve 5 by setting it to
position (1), see Fig. B-(A).
The product is ready to use.
4. Once you no longer need the prod-
uct, shut off the water supply by turn-
ing off the tap.
5. Open the hose connector valve
by turning the valve to position (1)
and allow the remaining water to
run off. After the water has drained,
the Product will return to its original
length.
NOTE!
- To release the hose from the tap or
the hose connector valve adapter
, slide the ring of the hose connec-
tor valve 4 , downwards as marked
with the arrow and unlock the cou-
pling and pull off the hose connector
valve 4 .
7. Cleaning and care instruc-
tions
CAUTION!
!
Danger of material damage!
- only clean with a damp cloth
- only use a a mild detergent
- do not use any strong detergents
and/or chemicals
- do not use sharp-edged tools such
as spatulas or similar, they can dam-
age the surface

8. Disposal

Disposal of the packaging
The packaging and oper-
ating instructions
01
PET
made of 100 % environ-
mentally friendly materials, which you
may dispose of at local recycling centres.
Disposal of the product
The product can be dis-
posed of with normal house-
hold waste.
9. Processing in case of
guarantee claim
To ensure quick processing of your con-
cern, please follow the instructions be-
5 low:
- Please have the till receipt and ar-
ticle number available (e.g. IAN
351637_2007) as proof of the pur-
chase.
- You can find the article number on
the rating plate on the product, as
an engraving on the product, the ti-
tle place of your instructions (bottom
left) or the sticker on the back or un-
3 derside of the product.
- If malfunctions or other defects oc-
cur, first contact the service depart-
ment below by telephone or e-mail.
- You can then send a product that
has been recorded as being de-
fective, including the proof of pur-
chase (till receipt) and stating what
the defect is and when it occurred,
postage-free to the service address
provided to you.
On www.lidl-service.com, you can down-
load these an many other manuals, prod-
uct videos and installation software.

10. Distributor

TRADIX GmbH & Co. KG
Schwanheimer Strasse 132
DE-64625 Bensheim/GERMANY

11. Service address

TRADIX SERVICE-CENTER
are c/o Teknihall Elektronik GmbH
Breitefeld 15
DE-64839 Münster/GERMANY
Hotline: 00800 30012001(free of
charge, mobile networks may vary)
E-Mail: tradix-gb@teknihall.com
E-Mail: tradix-ie@teknihall.com
11/2020 / PO31000538
Tradix Item No.: 351637-20-A
IAN 351637_2007
GB/IE
15