Fault Conditions; Data Table - Stiebel Eltron SHP-A 220 Plus Utilisation Et Installation

iNSTAllATiON
Specification
A1 Electronic assembly (control unit)
A2 Electronic assembly (programming unit)
C1 Condenser
E1 Heating element
F1 High limit safety cut-out TSR
F2 Motor overload relay M1
F3 High pressure limiter
F4 Fuse
G1 Impressed current anode
M1 Compressor
M2 Fan
N1 Thermostat TSR

16.3 Fault conditions

WARNING Burns
In the case of a fault, temperatures up to the high limit
safety cut-out limit can occur (see "Specification / Data
table" chapter).

16.4 Data table

Hydraulic data
Nominal capacity
Surface area, indirect coil
Application limits
Max. DHW temperature with heat pump
Max. DHW temperature with emergency/booster heater
Max. permissible DHW temperature inside the cylinder
High limit safety cut-out
Min./max. application limits for heat source
Minimum installation room volume (recirculation air mode, general do-
mestic use)
Maximum permissible operating pressure, cold water/DHW
Min./max. conductivity, drinking water
Output data to EN 16147
Nominal DHW temperature (EN 16147)
Nominal load profile (EN 16147)
Reference DHW temperature (EN 16147 / A20)
Reference DHW temperature (EN 16147 / A15)
Reference DHW temperature (EN 16147 / A7)
Maximum available nominal amount of DHW at 40 °C (EN 16147 / A20)
Maximum available nominal amount of DHW at 40 °C (EN 16147 / A15)
Maximum available nominal amount of DHW at 40 °C (EN 16147 / A7)
Rated heating output Prated (EN 16147/A20)
Rated heating output Prated (EN 16147 / A15)
Rated heating output Prated (EN 16147 / A7)
Heat-up time (EN 16147 / A20)
Heat-up time (EN 16147 / A15)
Heat-up time (EN 16147 / A7)
Power consumption, standby period (EN 16147 / A20)
Power consumption, standby period (EN 16147 / A15)
Power consumption, standby period (EN 16147 / A7)
COP (EN 16147 / A20)
COP (EN 16147 / A15)
COP (EN 16147 / A7)
Heating output
Average heating output (A20 / W10-55)
Average heating output (A15 / W10-55)
Average heating output (A7 / W10-55)
www.stiebel-eltron.com
R1 Resistance
S1 DIP switch
S2 DIP switch
T1 Temperature sensor (cylinder top/integral)
T4 Temperature sensor, evaporator
X0 Mains terminal
X1 Terminals
X3 Terminals
Behälter Cylinder
Deckel Cover
Mantel Jacket
SHP-A 220 Plus
238633
l 220
m²
°C 65
°C 65
°C
°C 92
°C +6/+42
m³ 23
MPa 0.8
μS/cm 100-1500
°C 55
L
°C 52.6
°C 52.7
°C 54.0
l 278
l 277
l 254
kW 1.6
kW 1.45
kW 1.01
h 6.06
h 6.65
h 8.78
kW 0.022
kW 0.027
kW 0.035
3.55
3.20
2.68
kW 1.9
kW 1.6
kW 1.3
SHP-A 300 Plus SHP-A 300 X
238634
302
65
65
92
+6/+42
23
0.8
100-1500
55
XL
54.4
54.1
54.2
395
412
410
1.52
1.63
1.14
9.05
8.83
12.52
0.024
0.028
0.040
3.51
3.26
2.79
1.9
1.6
1.3
SHP-A 220-300 Plus |
Plus
238635
291
1.3
65
65
70
92
+6/+42
23
0.8
100-1500
55
XL
54.4
52.5
52.6
371
387
381
1.43
1.41
1.07
9.05
9.60
12.43
0.028
0.032
0.044
3.51
3.30
2.75
1.9
1.6
1.3
31