Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPErATiON
Appliance description
2.2
General safety instructions
The appliance should only be operated once it is fully installed
and all safety equipment has been fitted.
WARNING Injury
!
The appliance may be used by children aged 8 and older
and persons with reduced physical, sensory or mental
capabilities or a lack of experience and know-how, pro-
vided that they are supervised or they have been in-
structed on how to use the appliance safely and have
understood the potential risks. Children must never play
with the appliance. Children must never clean the ap-
pliance or perform user maintenance unless they are
supervised.
WARNING Electrocution
Contact with live components presents a threat to life.
Damage to the insulation or to individual components
may result in a threat to life.
f If there is damage to the insulation, switch off the
f
power supply and arrange a repair.
All work on the electrical installation must be carried
out by a qualified contractor.
WARNING Burns
The water in the DHW cylinder can be heated to temper-
atures in excess of 60 °C. There is a risk of scalding at
outlet temperatures in excess of 43 °C.
f Ensure you do not come into contact with the water
f
when discharged.
WARNING Burns
Touching hot components can lead to burns.
f When working on hot components, always wear
f
protective working clothing and safety gloves.
The pipework connected to the DHW outlet of the appli-
ance can reach temperatures in excess of 60 °C.
WARNING Burns
In the case of a fault, temperatures up to the high limit
safety cut-out limit can occur (see "Specification / Data
table" chapter).
WARNING Burns
The appliance is filled with refrigerant at the factory.
In the event of refrigerant escaping due to a leak, avoid
coming into contact with the refrigerant or inhaling the
released vapours. Ventilate the rooms affected.
WARNING Electrocution
Never operate the appliance when the casing is open or
without a cover.
CAUTION Injury
!
If objects are left on the appliance, noise emissions may
increase due to resulting vibrations, and the objects
could fall and cause injury.
f Never place any objects on top of the appliance.
f
www.stiebel-eltron.com
Material losses
!
Ensure that the appliance, water pipes and safety valves
are free from the risk of frost. If you disconnect the ap-
pliance from the power supply, it is no longer protected
against frost or corrosion.
f Never interrupt the power supply to the appliance.
f
If voltage is supplied to the impressed current anode
and the PCB separately, the appliance remains protected
against corrosion.
Material losses
!
Keep the appliance installation site free from air contam-
inated with oil or salt (chloride) and corrosive or explo-
sive substances. Avoid contaminating the installation site
with dust, hairspray or substances containing chlorine
or ammonia.
Material losses
!
Covering the air intake or air discharge leads to a reduced
air supply. If the air supply is restricted, the operational
reliability of the appliance cannot be guaranteed.
f Never cover the appliance.
f
Material losses
!
Only operate the appliance when the DHW cylinder has
been filled. If the DHW cylinder is empty, safety equip-
ment switches off the appliance.
Material losses
!
Heating liquids other than potable water is not permitted.
Note
The appliance's DHW cylinder is pressurised. During the
heat-up process, expansion water will drip from the safe-
ty valve.
f If water continues to drip when heating is complet-
f
ed, please inform your qualified contractor.
2.3
Test symbols
See type plate on the appliance.
3.
Appliance description
The fully wired appliance enables DHW to be supplied efficiently
to several draw-off points using renewable energy. The appliance
extracts heat from the intake air. This heat is used to heat up the
water in the DHW cylinder with added electric power. The amount
of electric energy and time required to heat up the DHW depend
on the temperature of the air drawn in. When the air intake tem-
perature drops, the heat pump's heating output is reduced and
the heat-up time is extended.
The appliance is designed for indoor installation. The appliance
operates in recirculation air mode and does not require outdoor
air.
Heat extraction can result in a drop in ambient temperature in
the installation room of between 1 °C and 3 °C. The appliance
also extracts moisture from the air, which turns into condensate.
The condensate is removed from the appliance via the condensate
drain.
SHP-A 220-300 Plus |
5
Publicité
Chapitres
Table des Matières
Dépannage
