Temperature Display; Setting The Alarm Time; Activating/Deactivating The Alarm; Backlight - Hama RCR 110 Mode D'emploi

Masquer les pouces Voir aussi pour RCR 110:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
Note – Day of the week
You can choose German (GE), English (EN), Italian (IT), Spanish
(SP) or French (FR) for the weekday display.
Setting the time zone
Note – Time zone
• The DCF signal can be received over long distances, but
always transmits the current Central European Time in
Germany. Make sure you account for the time difference in
countries with another time zone.
• If you are in Moscow, the time is 3 hours later than in
Germany. This means that you should set +3 for the time
zone. The clock then automatically sets the time to 3 hours
after the DCF signal received or relative to the manually
set time.
• Press and hold the ▲ button (3) for approx. 3 seconds until the
time zone symbol
is displayed.
F
• Press and hold the MODE button (4) for approx. 3 seconds to
set the required time zone difference.
• To select the individual values, press the ▲ button (3) or the 
button (2) and confirm each selection by pressing the MODE
button (4).
• Press and hold the ▲ button (3) for 3 seconds to switch the
display between local and time zone-shifted time.
Selecting 12 or 24-hour format
• Press the ▲ button (3) to switch between the 12 and 24-hour
formats.
Selecting weekday/calendar week display
• Press the  button (2) to switch between displaying the
weekday and the calendar week (WEEK).

5.3. Temperature display

• Press the °C/°F/WAVE button (5) to choose between °C and °F
for the temperature display.
5.4. Alarm
Note – Alarm
The alarm time always depends on the time displayed, that is,
the local or time zone-shifted time (
).
F

Setting the alarm time

• Repeatedly press the MODE button (4) to access alarm mode 1
(AL1) or 2 (AL2).
• Press and hold the MODE button (4) to set the alarm time for
the alarm displayed. The hours display begins to flash.
• Press the ▲ button (3) or the  button (2) to select the hour for
the alarm time and confirm your selection by pressing the MODE
button (4). The minutes display begins to flash.
• Repeat the process to set the minutes for the alarm time.
• Press the MODE button (4) repeatedly to also set the other
alarm mode or return to the temperature display.

Activating/deactivating the alarm

• Press the
button (9) repeatedly to activate/deactivate alarm
1 or alarm 2.
• If an alarm is activated, the corresponding symbol
be displayed.
Stopping the alarm/snooze function
• If the alarm is triggered, the alarm symbol
flash and an alarm will sound.
• Press the
button (9) to stop the alarm. Otherwise, it will stop
automatically after 4 minutes.
Note – Snooze function
While the alarm signal is sounding, press the LIGHT-SNOOZE
button (1) to activate the snooze function. The alarm symbol
(7)
/
and Z
will begin to flash. The alarm signal will be
z
stopped for 4 minutes, after which it will sound again.
5.5. Dual Time settings and display
• Dual Time allows you to set and display a second, completely
independent time (8).
• Press the MODE button (4) repeatedly until SECOND TIME
is displayed.
• Press and hold the MODE button (4) for approximately 3
seconds. The hours display begins to flash.
• Press the ▲ button (3) or the  button (2) to select the hour
and confirm your selection by pressing the MODE button (4).
The minutes display begins to flash.
• Repeat the process to set the minutes.
• To select the individual values, press the ▲ button (3) or the 
button (2) and confirm each selection by pressing the MODE
button (4).

5.6. Backlight

If you press the LIGHT-SNOOZE button (11), the display will light
up for approx. 5 seconds.
/
will
/
will begin to
5

Publicité

Table des Matières
loading

Table des Matières