Bosch PFS 3000-2 Notice Originale page 21

Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Ensure that the spray gun and base unit are as-
u
sembled completely and with all seals. Only this will en-
sure the function and safety of the fine-spray system.
Connecting the Air Hose (see figures A1–A3)
– Open the elastic band (27) and completely unwind the air
hose (18).
Connecting the base unit:
– Insert a bayonet lock (19) of the air hose securely into the
holes in the base unit port (28) according to the arrow
marks.
– Turn the bayonet lock a quarter turn clockwise.
Connecting to the spray gun:
– Insert the second bayonet lock (19) of the air hose se-
curely into the holes in the spray gun port (8) according
to the arrow marks.
– Turn the bayonet lock a quarter turn clockwise.
Note: Remove the air hose (18) before pouring in spray ma-
terial (quarter turn of the bayonet lock (19) anticlockwise;
pull the bayonet lock (19) out of the port (8)).
Changing the Nozzle Cap (see figures B1–B2)
The fine-spray system is supplied with two nozzle caps:
(9)
Paint White
Delivery condi- Mounted
tion
Application "Wall"
Note: Check the spray material by stirring it before selecting
the nozzle cap. Thin-viscosity material (e.g. wood paint) can
be sprayed better with the grey nozzle cap (10). Thick-vis-
cosity material (e.g. wood lacquer or wall paint) can be
sprayed better with the white nozzle cap (9).
– To change the nozzle cap, unscrew the cap nut (3).
– Pull off the air cap (2).
– Unscrew the mounted nozzle cap.
– Open the air filter cover (25) and take the required nozzle
cap out of the accessory compartment (29).
– Screw the required nozzle cap into the thread in the spray
gun.
– Put the air cap (2) on the nozzle cap and tighten it with
the cap nut (3).
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Bosch Power Tools
u
Work preparation
u
When purchasing paint, lacquer and spray material, pay at-
tention to their environmental compatibility.
Preparing the spray surface
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding
When spraying, all non-covered surfaces can be soiled by
the spray mist. Therefore, thoroughly prepare the area
around the surface to be sprayed:
– Cover or mask off floors, furnishings, doors, windows as
Preparing the spray material
– Stir the spray material thoroughly.
– Dilute the spray material if necessary.
Spray material
Oils, glazes, impregnations, anti-rust
primers
Nozzle cap Solvent-dilutable or water-dilutable lac-
quers, primers, radiator lacquers, thick-
(10)
coat glazes
Grey
Emulsion paint, latex paint
In the accessory com-
u
partment (29) under
the air filter cover (25)
"Wood"
u
Filling the spray material (see figures C1–C2)
Note: Remove the air hose (18) before pouring in spray ma-
terial (quarter turn of the bayonet lock (19) anticlockwise;
pull the bayonet lock (19) out of the port (8)).
– When using large buckets, pour the spray material into a
– Hold the spray gun in place with one hand and
– Pull the spray gun off the container (7).
– If you are using already opened spray material, place the
Products that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
dust.
well as door and window frames, etc.
When diluting, make sure that the spray material and
the diluting agent are compatible. When using a faulty
diluting agent, lumps can develop that can lead to clog-
ging of the spray gun.
When diluting the spray material, make sure that the
flash point of the mixture is above 55 °C again after di-
luting. Diluting substances such as solvent-based lac-
quers lowers the flash point.
smaller transfer bucket (12) if necessary (e.g. 10 l wall
paint into an empty 2.5 or 5.0 l bucket).
use the other hand to turn the container (7)
towards the open symbol.
thoroughly cleaned filling sieve (11) on the container (7)
to hold back any lumps of paint when pouring in.
1 609 92A 58D | (28.10.2019)
English | 21
Recommended
dilution
0%
0–10%
0–10%