Publicité
Les langues disponibles
Les langues disponibles
SIM card
The Fence Control communicates with any
mobile phone that can send and receive SMS.
To do this, a MICRO SIM card must be inserted
into the Fence Control. Depending on the
mobile phone provider selected, mobile phone
charges may apply for the SMS service.
Commissioning
1. Deactivate the PIN on the SIM card. Top up SIM card call credit.
2. Carefully open the casing. Insert the
SIM card according to the instructions
inside.
3. Connect the Fence Control's internal
battery. The Fence Control should now
start.
4. Carefully close the housing and make
sure the seal is secure. Screw the housing
hand-tight with Phillips screws so that
the housing is watertight.
5. Connect the Fence Control to the power supply. When all LEDs flash simultaneously
every five seconds, the internal battery is charging. This can take up to ten minutes.
6. As the Fence Control logs on to the mobile phone network, all the LEDs light up in
short succession (rotating light). After successful login, the power supply and mobile
range LEDs illuminate simultaneously for one second at five-second intervals.
7. Send the SMS command abo 1234 to the phone number of the inserted SIM card.
8. The Fence Control is now activated and the fence system can be controlled via SMS
commands. You will now receive alarms and alerts in case of problems with your fence
system.
9. More SMS commands can be found in the user manual. Visit the website
www.gallagher.eu or scan the QR code on the front of this manual with your smartp-
hone.
First SMS commands
STANDARD
MICRO
NANO
EXAMPLE RESPONSE FROM FENCE CONTROL
Welcome!
+xx xxx xxx xx xx xx
stored in the Fence Control's
phone list.
Authorised: Fence Control: PIN
new -yourpasswordhere-
ALL 3 COMMANDS GIVE THE ANSWER
Fence Control: On
Voltage fence: 6500V
Power supply: 11.7V
LTE: 59%
Temperature: 20 degrees C.
COMMAND TO REGISTER A NEW
TELEPHONE NUMBER
abo 1234
ASSIGNMENT OF A NEW SECURITY PIN
new pin -yourpasswordhere-
SWITCH ON ENERGISER
Enable
SWITCH OFF ENERGISER
Disable
QUERY STATUS
info
LIST OF ALL COMMANDS
help
What can the Fence Control do?
• Monitoring the fence and voltage supply on the voltage fence
• Switching the fence system on and off via mobile phone
• Alert in case of acute problems with the fence system
• Checking the functionality of the selected fence wire. If your fence has a
problem, you will receive an alert by text message.
• And much more!
What to do if ...
the LEDs light up simultaneously for one second at five-second intervals?
The internal battery is charging. Wait up to 2 hours for the battery to charge.
the LEDs do not flash or do not light up?
Check that the battery in the Fence Control is connected and make sure the
Fence Control is properly powered.
the LEDs light up in short succession?
The Fence Control cannot find a mobile phone network or cannot log in. Check
the mobile range. Deactivate PIN on SIM card.
The power supply voltage LED lights up only very briefly or not at all?
Power supply voltage is too low or missing. Replace or charge the power supply
or external battery. Check the power supply connection.
The mobile range LED is lit only briefly?
The reception of the Fence Control is very weak. Check whether a mobile phone
network is available at your location.
Fence Control does not send an SMS response to a query SMS?
Check whether you are included in Fence Control's phone list. To do so, send the
SMS command abo 1234 to Fence Control. A SIM card with call credit must be
inserted.
I can't access the Fence Control's WEB?
Try sending the 'Web on' command. Check if your Fence Control has a SIM card
with call credit available.
The Fence Control provides more security on the meadow.
If you have any questions or suggestions, please do not hesitate to
contact us.
Gallagher Animal Management
GallagherEuropeBV
gallagher.eu
Publicité
