Lubrication; Disassembly - BEAL NPMS15.5/107H Notice D'emploi

7. Mow for a short distance. If the height of cut is not
level, repeat the above steps.

Lubrication

Where To Lubricate (Figure 15)
Models with grease fittings: Lubricate with
grease gun.
Apply grease with a brush to the areas shown.
Lubricate the areas shown with engine oil.
NOTE: Apply grease to the steering gear as sembly.
CAUTION: If the unit is operated in dry areas that have
sand, use a dry graphite spray to lubricate the unit.
Check The Tyres
Check the air pressure in the tyres. Tyres with too much air
pressure will cause the unit to ride rough. Also, the wrong
air pressure will keep the mower housing from cutting level.
The correct air pressure is: Front Tyres 0,97 BAR (14 PSI),
Rear Tyres 0,69 BAR (10 PSI).

Disassembly

How To Replace The Motion Drive Belt
1. Remove the mower housing. See the instruc tions on
"How To Remove The Mower Hous ing".
2. (Figure 16) Remove the
3. Disconnect the idler spring (G).
4. Remove the idler pulley (H) and spacer (I).
5. Remove the V-idler pulley (E) and spacer (M).
6. Remove the motion drive belt (A) from the drive
pulley (F).
7. (Figure 17) To remove the
the stack pulley (B), pull the front end of the belt under
the stack pulley (B) and then back between the stack
pulley and the steering plate (C).
8. (Figure 11) Remove the
9. Remove the two screws (K) that attach the steering
shaft assembly (L). Raise the steering wheel and
steering shaft assembly (L). Pull the motion drive belt
(A) under the steering shaft assembly (L).
mid-idler pulley (D).
motion drive belt (A) from
access panel (J).
10. Remove the motion drive belt (A). A correct
replacement part or assistance is available from an
Authorized Service Center in your area.
11. To install the motion drive belt, reverse the above
steps.
12. (Figure 16) Check the routing of the
belt (A). Make sure the motion drive belt is installed
correctly on the idler pulleys.
13. Before you use the unit, check the adjust ment of the
clutch. See the instructions "How To Check And Adjust
The Clutch".
14. Install the mower housing. See the instruc tions "How
To Install The Mower Housing".
How To Replace The Mower Drive Belt (Figure 10)
1. Remove the mower housing. See the instruc tions on
"How To Remove The Mower Hous ing".
2. Remove the pulley guard.
3. Pull the belt retainer (A) away from the idler pulley (B)
and remove the mower drive belt (C).
4. Pull the belt retainer (D) away from the right mandrel
pulley (E) and remove the mower drive belt (C).
5. Pull the belt retainer (D) away from the left mandrel
pulley (F) and remove the mower drive belt (C). A
correct replacement part or assistance is available from
an Authorized Service Centre in your area.
6. To install the mower drive belt, reverse the above steps.
How To Remove The Mower Housing (Figure 22)
1. Move the blade rotation control (A) to the DISENGAGE
position.
2. Move the lift lever (B) to the level adjust ment position.
CAUTION: The lift lever is spring loaded. Make sure the lift
lever is locked in the LEVEL ADJUSTMENT position.
3. Remove the hair pins and the washers from the
adjuster arms (C). See illustrations "3" and "4".
4. Remove the hair pins and washers from the
links (D). See illustrations "1" and "2".
5. Disconnect the extension spring (E) from the blade
control rod (F). See illustration "5".
6. Disconnect the front hanger (I) from the axle support.
See illustration "6".
7. Remove the mower drive belt (G) from the stack
pulley (H).
8. Pull the mower housing away from the right side of the
unit.
9. To install the mower housing, reverse the above steps.
motion drive
suspension
21