EINHELL GC-CF 18/110 Li Instructions D'origine page 15

•
The cordless blower will then come on at the
lowest level.
Switching off :
•
Press the On/Off switch (7) again.
6.2 Adjusting the blower level (Fig. 5)
•
The blower has three setting levels for indivi-
dual adjustment to the particular situation.
•
The cordless blower always switches on at
the lowest level.
•
To raise the blower level, press on the blower
level selector (8).
•
The blower level will go up one level with
each press.
•
The current blower level is shown by the blo-
wer level indicator (9).
6.3 Adjusting the blower position
a) The vertical blower position is infi nitely adjus-
table (approx. 300° possible) by turning the
blower head (Fig. 1 / Item 1) .
b) The horizontal blower position is infi nitely ad-
justable (approx. 290° possible) by turning the
blower head holder (Fig. 1 / Item 3) .
6.4 Fastening the cordless blower (Fig. 6)
The cordless blower is fastened with the rotata-
ble clamping part (Item 6). It has two diff erently
shaped surfaces. The surface with the semicircu-
lar recess is suitable in particular for pipes (min.
Ø20 mm), the other for level surfaces (e.g. table
tops). To fasten, press the clamping lever (Item 4)
downwards, move e.g. the table top between the
clamping part (Item 6) and the clamping surface
(Fig. 1 / Item 5a), and release the clamping lever
again. Clamping is also possible between the
clamping lever and the clamping surface.
Caution! Always check for secure clamping.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
Anl_GC_CF_18_110_Li_SPK13.indb 15 Anl_GC_CF_18_110_Li_SPK13.indb 15
GB
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage
Remove the rechargeable battery/batteries. Store
the equipment and accessories in a dark and dry
place at above freezing temperature. The ideal
storage temperature is between 5 and 30 °C.
Store the electric tool in its original packaging. If
the appliance is to be stored unused for a long
period, the batteries are removed.
- 15 -
12.03.2024 08:49:33 12.03.2024 08:49:33