Installation Instructions - GE GLC4000 Série Instructions D'installation

Installation Instructions

STEP 1 REMOVE WOOD BASE
IMPORTANT
– Do not kick off wood base! Damage
will occur.
• Move the dishwasher close to the installation location and
lay it on its back.
• Remove the four skid bolts on the underside of the wood
base with 3/8" nut driver.
• Discard base and bolts.
• Upright the dishwasher.
STEP 2 INSTALL FAUCET ADAPTER
The special faucet adapter supplied with your dishwasher
must be attached to the sink faucet before you can use your
dishwasher.
The faucet adapter is designed to fit standard spouts having
internal or external threads. You will find the adapter and two
washers in the faucet adapter packet in your dishwasher.
Attach the Faucet Adapter
ring on your faucet spout.
External Threads
• If faucet has external threads: Insert the
thinner of the two washers into the faucet
adapter and attach it to the faucet spout.
• Tighten with pliers.
Internal Threads
• If faucet has internal threads: Insert both
of the washers into the faucet adapter and
attach it to the faucet spout.
• Tighten with pliers.
Non-Standard Threads
• If the faucet adapter threads do not match
your faucet spout, your local hardware or plumbing supply
spout to the special faucet adapter.
CAUTION:
A sink spray attachment hose can
burst if it is installed on the same faucet as your dishwasher.
We suggest that you disconnect the sink spray attachment,
if your sink has one, and place a cap over the opening.
STEP 3 CONNECT THE UNICOUPLE
TO THE FAUCET
• Run garbage disposer,
if you have one, to
clean out the disposer
and thus allow water
to drain from the sink
through the disposer
and down the drain.
• Run hot water faucet
to purge cold water from
the hot water line. The hot water must be between 120°F and
150°F for best wash performance.
• Roll the dishwasher to a position just in front of the sink.
• Pull the unicouple and its hoses completely out from storage
compartment at rear of the dishwasher.
• Attach the unicouple to the faucet adapter following the
three steps below:
– Depress the locking collar at the top of the unicouple.
– Place the unicouple completely over the faucet adapter.
– Release the locking collar. The unicouple should now be
locked onto the faucet adapter.
• Turn on the hot water faucet and check for leaks. If a leak is
detected, disconnect the unicouple, and refer to Step 4.
Note: The unicouple's small hose carries water from the
faucet to the dishwasher. The large hose carries water from
the dishwasher to the sink. Orient the faucet with the
unicouple attached so water from the unicouple will run into
the sink drain.
STEP 4 FAUCET ADAPTER LEAK
Skip this step if no unicouple leak was observed.
If a unicouple leak was observed in Step 3, take whatever
actions are necessary to repair the leak. This may be as simple
as tightening the faucet adapter. Or, it may require the services
of a plumber if water is leaking from the interface between the
moveable faucet arm and the fixed part of the faucet fastened
to the sink.
STEP 5 PRETEST CHECK LIST
Review this list after connecting your dishwasher to avoid
charges for a service call that is not covered by your warranty.
Open the door and remove all foam and paper packaging.
Locate the Owner's Manual.
Read the Owner's Manual to familiarize yourself with the
operation of the dishwasher.
Remove the protective film, if present, from the control
panel.
Add 2 quarts of water to the bottom of the dishwasher
to lubricate the pump seal.
Collar
3