Bosch GOP 12V-28 Professional Notice Originale page 10

10 | English
Application tool
AVZ 70 RT4
Starlock
70 mm wide
carbide-RIFF mor-
tar remover
AVZ 90 RT2
Starlock
90 mm wide
carbide-RIFF delta
plate for mortar
and abrasive ma-
terials
AVZ 93 G
Starlock
93 mm-wide sand-
ing plate for sand-
ing sheets of the
Delta 93 mm series
AUZ 70 G
Starlock
70 mm wide profile
sander for
70 × 125 mm
sanding sheets
AVZ 32 RT4
Starlock
32 × 50 mm
carbide-RIFF sand-
ing finger for wood
and paint
AIZ 28 SC
Starlock
28 × 40 mm HCS
universal joint cut-
ter
ASZ 32 SC
Starlock
24 mm-wide HCS
pull cutting edge,
11 mm-wide HCS
push cutting edge
ATZ 52 SC
Starlock
52 mm scraper, ri-
gid
Fitting/changing the application tool
Remove the application tool if one has already been fitted.
To remove the application tool, use the hex key (12) to
loosen the clamping bolt (11) and remove the tool.
Position the required application tool (e.g. plunge cut saw
blade (10)) on the tool holder (7) so that the depressed
1 609 92A 5YG | (21.08.2020)
Material Application
Mortar, joints, epoxy Reaming and separating joint and tile material, as well as
resin, fibreglass-rein- rasping and sanding on a hard substrate; long service life
forced plastics, abrasive thanks to BOSCH carbide technology;
materials Example: Removing tile adhesive and grout
Mortar, concrete residue, Rasping and sanding on a hard substrate;
wood, abrasive materials, Example: Removing mortar or tile adhesive (e.g. when re-
paint placing damaged tiles), removing carpet adhesive
residues, removing paint residues;
available in grain sizes 20 (RT2), 40 (RT4), 60 (RT6) or
100 (RT10)
Depends on the sanding Sanding on edges, in corners or in difficult-to-access
sheet areas;
depending on sanding sheet, e.g. for sanding wood, paint,
lacquer, stone;
non-woven materials for cleaning and for structuring
wood, removing rust from metal and for abrading lac-
quers, polishing felt for pre-polishing
Wood, pipes/profiles, Convenient and efficient sanding of profiles and curved,
paint, varnish, filler, metal uneven material surfaces up to a diameter of 55 mm;
sanding sheets for sanding wood, pipes/profiles, varnish,
filler and metal
Wood, paint Sanding wood or paint in difficult-to-access places without
sanding paper; long service life thanks to BOSCH carbide
technology;
Example: Sanding down paint between window shutter
slats, sanding wooden flooring in corners;
available in grain sizes 40 (RT4) and 100 (RT10)
Expansion joints, window Cutting soft materials;
putty, insulation materials example: Cutting silicone expansion joints or window
(rock wool) putty
Roofing felt, carpets, arti- Quick and precise cutting of soft material and flexible, ab-
ficial turf, cardboard, PVC rasive materials;
flooring Example: Cutting carpets, cardboard, PVC flooring, re-
cesses in roofing felt
Carpets, mortar, con- Scraping on a hard substrate;
crete, tile adhesive Example: Removing mortar, tile adhesive and concrete
and carpet adhesive residues;
available as flexible scraper ATZ 52 SFC (soft carpet ad-
hesive/paint residues)
centre is facing downwards (see figure on the graphics page,
text on the application tool should be legible from above).
Turn the application tool to a position which is convenient
for the job at hand and allow it to lock into place in the cams
of the tool holder (7). Twelve positions offset by 30° are
possible for this.
Bosch Power Tools