EINHELL TC-MT 150 E Instructions D'origine page 16

5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Mounting on a wall (Fig. 3/Item 6)
The equipment holder (6) can be fastened to a
wall using the mounting holes (a) provided. The
correct dimensions for the drill holes can be found
on the back of the equipment holder (6).
5.2 Winding up the power cable
(Fig. 4 / Item 6)
Wind the attached power cable (b) around the
equipment holder (6) as shown in Fig. 4.
5.3 Inserting the various tools (Fig. 5)
Danger! Before inserting a tool (and before each
tool change) switch of the drive unit and pull the
power plug.
1. Press the locking knob (3) and turn the collet
chuck until the bolt locks into place.
2. Remove the clamp nut (4), insert the mat-
ching clamping sleeve (23) and refi t the
clamp nut.
3. Insert the required tool into the sleeve and
tighten the collet chuck nut (4).
The projection is not allowed to exceed 22 mm!
5.4 Fitting the fl exible shaft (Fig. 6/ Item 7)
•
Unscrew the cover (5) from the front of the
equipment.
•
Remove the clamp nut (4), insert the 3.2 mm
clamping sleeve (23) and refit the clamp nut.
•
Insert the internal axle (c) of the flexible shaft
into the clamping sleeve (23).
•
Tighten the clamp nut (4).
•
Now tighten the ring (d) on the multiple grin-
der/sander.
5.5 Inserting the various tools into the fl exib-
le shaft (Fig. 7/Item 7)
1. Press the locking knob (e) and turn the collet
chuck until the bolt locks into place.
2. Remove the clamp nut (4), insert the mat-
ching clamping sleeve (23) and refi t the
clamp nut.
3. Insert the required tool into the sleeve as far
as the stop and tighten the clamp nut.
Anl_TC_MT_150_E_SPK13.indb 16 Anl_TC_MT_150_E_SPK13.indb 16
GB
5.6 Storing the accessories (Fig. 8)
Frequently used accessories can also be inserted
in the holes provided (f) for quick removal.
6. Using the tool for the fi rst time
•
Make sure that the drive unit is switched off.
•
Check that the mains voltage specified on the
rating plate of the power supply unit is the
same as your mains supply. Only then should
you insert the plug of the power supply unit
into a socket-outlet.
6.1. ON/OFF switch (Fig. 1 / Item 1)
Turn on the equipment by setting the On/Off
switch (1) to "I".
Turn off the equipment by setting the On/Off
switch (1) to "0".
6.2. Speed selector (Fig. 1 / Item 2)
The required speed can be set with the speed
control (2).
The correct speed depends on the tool used and
the type of material being processed (see point
6.5).
6.3 Directions for use
•
With small milling cutters / grinding pins: Use
a high speed.
•
With large milling cutters / grinding pins: Use
a low speed.
6.4 Tips
•
Exert only moderate pressure on the workpi-
ece and allow it to be processed at uniform
speed.
•
You will not finish your work sooner by exer-
ting heavy pressure. On the contrary, heavy
pressure will cause the drive unit to slow
down or stop and will overload the motor.
•
For your own safety, use a vise or screw
clamp to secure small workpieces.
•
Precision work/engraving: Hold the drive unit
like a pen (single-handed).
•
Rough work: Hold the drive unit like the hand-
le of a hammer (two-handed).
6.5 Description of the accessories (Fig. 2)
Drill bits, 1.6 / 2.4 / 3.2 mm (8)
For drilling in wood and soft metal.
Recommended speed setting: ≤ 6
- 16 -
07.05.2024 13:30:40 07.05.2024 13:30:40