Device Information; Operating Limits - Dimplex LA 14PMS Instructions D'installation Et D'utilisation

11

11 Device Information

1 Type and order code
2 Design
2.1 Controller, external
2.2 Thermal energy metering
2.3 Installation location / degree of protection according to EN 60 529
2.4 Frost protection condensate tray / heating water
2.5 Performance levels
3

Operating limits

2
3.1 Heating water flow / return
3.2 Air (heat source)
4 Performance data / flow rate
4.1 Heating water flow rate / internal pressure differential
maximum
minimum
4
4.2 Heat output / COP
4.3 Sound power level according to EN 12102
4.4 Sound pressure level at a distance of 10 m
5
(air outlet side)
4.5 Air flow
5 Dimensions; weight and filling quantities
5.1 Device dimensions without connections
5.2 Device connections for heating system
5.3 Weight of the transportable unit(s) incl. packaging
5.4 Refrigerant; total filling weight
5.5 Lubricant; total filling quantity
6 Electrical connection
6.1 Supply voltage; fuse protection
6.2 Starting current with soft starter
6.3 Nominal power consumption at A2/W35 /
max. power consumption
Nominal current at A2 / W35 / cos ϕ
6.4
6.5 Max. power consumption of compressor protection
(per compressor)
7 Complies with the European safety regulations
8 Additional model features
8.1 Type of defrosting
8.2 Max. operating overpressure (heat sink)
1. The heat circulating pump and the heat pump controller must always be ready for operation.
2. At air inlet temperatures of -25 °C to -10 °C flow temperature rising from 50 °C to 65 °C
3. These data indicate the size and capacity of the system according to EN 14511. For an analysis of the economic and energy efficiency of the system, the bivalence point and
regulation should be taken into consideration. These specifications can only be achieved with clean heat exchangers. Information on maintenance, start-up and operation can be
found in the respective sections of the installation and operating instructions.
The specified values have the following meaning, e.g. A7 / W35: Heat source temperature 7 °C and heating water flow temperature 35 °C.
4. With minimum heating water flow.
5. The specified sound pressure levels correspond to the operating noise of the heat pump in heating operation with a flow temperature of 35 °C.
6. Note that additional space is required for pipe connections, operation and maintenance.
7. See CE declaration of conformity
EN-8
1
°C
°C
3
m³/h / Pa
m³/h / Pa
at A7 / W35 kW / ---
kW / ---
at A2 / W35 kW / ---
kW / ---
at A7 / W35 kW / ---
kW / ---
at A7 / W55 kW / ---
kW / ---
at A10 / W35 kW / ---
kW / ---
dB(A)
dB(A)
m³/h
6
H x W x L cm
Inches
kg
type / kg
type / litres
V / A
A
3
kW
A / ---
W
bar
LA 14PMS
External
---
Outdoor / IP 24
Heated / yes
2
up to 65 ± 2 / from 18
-25 to +35
2.4 / 10100
1.0 / 3200
EN 14511
8.0 / 2.5
4.0 / 2.0
10.2 / 3.1
5.8 / 2.9
13.3 / 3.6
7.4 / 3.7
11.7 / 2.8
6.3 / 2.6
14.5 / 3.9
8.1 / 4.0
63
35
4500
1571 x 852 x 1552
R 1 1/4"
256
R290 / 1.8
Alkyl benzene (AB) / 1.9
1~ / N / PE 230V (50Hz) / C32A
28
3.3 / 6.0
18.0 / 0.8
---
7
Hot gas
3.0