Top Panel - Alesis MultiMix 8 USB FX Guide D'utilisation

Features

Top Panel

1. Power LED: Illuminates when
the MultiMix 8 USB FX is on.
2. Phantom Power LED: Lights
up when phantom power is
engaged.
3. Main Out: Use standard 1/4"
cables to connect this output
to the house speaker or
amplifier system. The level of
this output is controlled by the
Main Volume knob.
4. Monitor Out: Use standard
1/4" cables to connect this
output to your monitor speaker
or amplifier system. The level
of this output is controlled by
the Monitor Volume knob.
5. Phones: Connect your 1/4"
headphones to this output. The
Phones knob controls volume.
6. Aux Send Output: You may
connect the
external device (usually an
outboard effects device) to this
output with a 1/4" mono cable.
This output can also be used
to create a custom monitor mix
for onstage musicians. You
can adjust the level with the
Aux Return Level knob.
7. Aux Return Inputs: You may connect the outputs of an external device to these inputs with 1/4"
mono cables. This is usually used for outboard effects devices but can also be used like an extra input
channel for synthesizers, drum machines, etc. If your source is mono, plug it into the left jack and it
will be heard on both the left and right sides.
8. 2 Track Inputs: You may connect the outputs of an external recording device to these inputs using
standard RCA cables. This can be used to listen to a 2-track recording you've just made, or to
connect to a personal media player to play pre-recorded music before your live gig. Press the 2
TRKS/USB To Monitor button to hear this in your headphones or monitor speakers. Press the 2
TRKS/USB To Main to hear this in the house speakers.
9. 2 Track Outputs: You may connect an external recording device to these outputs using standard
RCA cables.
10. Footswitch: When a footswitch is connected to this jack with
a 1/4" TRS cable, it can be pressed to allow all channels to
bypass MultiMix 8 USB FX's internal effects processor. This
jack supports Boss FS-5L and FS-6 pedals or other latching-
type footswitches (not included).
11. Mic Input: Connect a microphone to these inputs with an XLR
cable.
12. Line Input: Connect line-level devices to these inputs with 1/4"
cables.
13. Insert: The insert jack allows you to insert a compressor, EQ,
or any other signal processor in between the MultiMix 8 USB
FX's preamplifier and A/D converter. Use a standard 1/4" TRS
cable when connecting a device to this insert.
6
14
24 24
23 23
22 22
21 21
26 26
input of an
25 25
19 19
17
11 11 11 11
12 12 12 12
13 13
14 14
15 14
16 16 16
16
24 24
22 22
21 21
26 26 26 26
25 25 25 25
19 19
17 17 17
18 18 18 18
6
3
4
7
10
12 12
8 9
27
24 24
29
21 21
28
20 20
35
17 17
When using Line Inputs 5/6, 7/8, and
the Aux Returns:
• If only the left channel is used, the
signal will be heard in both left and
right channels and the balance will
not be adjustable.
• If only the right channel is used, the
signal will be heard in the right
channel only.
Use standard 1/4" TRS (tip-ring-sleeve)
cables when connecting devices to the
Insert jacks. The signal is sent from the
tip of the cable and returns on the ring.
TRS (tip-ring-sleeve)
TS (tip-sleeve)
5
1 2
30
33
32
31
36
34