Publicité
Les langues disponibles
Les langues disponibles
EnGLIsH
Your tool features a keyless chuck
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Turn tool off and disconnect tool from power source.
2. Grasp the black sleeve of the chuck
use the other hand to secure the tool. Rotate the sleeve
anticlockwise (as viewed from the front) far enough to
accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full gripping power.
nOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector that allows 3 modes
17
to be customized using the Tool Connect™ app. Home
settings are active when the home indicator
Table 1 for customizable features.
Once configured, pressing the mode button
the tool will cycle through the modes
If you are unsure of the current configuration, press the mode
selector button
14
to set the tool to the Home setting (home
indicator
is lit).
16
D
WALT Tool Connect™
e
WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™ interaction.
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button
14
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D
WALT Tool Connect™ is an application for your smart device
e
(such as a smart phone or tablet) that connects the device to
TaBLE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM)
Speed 1
in Drill Mode
Speed 2
Speed 3
Bind-Up Control®
38
with one rotating sleeve for
6
with one hand and
6
16
is lit. Refer to
on the foot of
14
17
.
(Fig. D) to set the tool to the
Home
MED
20 secs
450
1300
2000
Disabled
Disabled
your tool to allow you to configure specific tool functions. Refer
to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D
WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D
WALT Tool Connect™ application at:
e
•
Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
•
Follow the instructions in the app to create your Tool
Connect™ account.
•
On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
•
To connect your tool with the D
at the appropriate screen, press the mode selector button
14
for 3–5 seconds, then wait for the tool to connect. The
tool can only be connected to one Tool Connect™ account
at a time.
Once the tool has been connected, you can confirm that you
would like to register the product.D
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D
WALT service center. Do not attempt to replace the coin cell
e
battery yourself.
WARNING: Danger of explosion if battery is
incorrectly replaced.
WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
•
Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
Factory Presets
Mode 1
Mode 2
OFF
MED
20 secs
20 secs
450
450
1300
1300
2000
2000
Disabled
WALT Tool Connect™ app,
e
WALT.com account.
e
Customizable
Mode 3
Range
HIGH
OFF-HIGH
20 minutes
0–20 minutes
450
140–450
1300
400–1300
2000
600–2000
Disabled/
Disabled
Enabled
Publicité
