Applications; Impacting Techniques - Milwaukee M12 FUEL SURGE Manuel De L'utilisateur

Attaching and Removing
Accessories
This driver is intended for use with drill
and driver bits with a 1/4" hex shank
and ball detent recess.
1. To attach an accessory, press the
shank into the hex drive chuck.
2. To remove the accessory, pull out
the chuck ring and remove the ac-
cessory. Release the ring.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up for
2-3 seconds.
To signal the end of charge, 1 light on the fuel gauge
will flash for 2-3 seconds.
Using the Drive Control
The drive control button
is used to adjust the
rotation speed (RPM)
for the application.
To select the drive
control mode:
1. Pull and release the
trigger to turn on the
tool. The current in-
dicator is lit.
2. Press the drive control button
the 4 modes. When the desired mode indicator is
lit, begin work.
Mode 1
RPM 0 - 1 100 0 - 2 200 0 - 3 200
IPM 0 - 950 0 - 2 200 0 - 3 400
The function is designed to reduce screw strip-
ping, screw breakage, and damage to the work sur-
face when driving self-tapping screws. This function
is optimized for the most common materials, including
#8, #10 and #12 self-tapping screws between 1/2"-1"
in length and 18-22 gauge sheet metal.
NOTE:
mode will only run if the trigger is pulled
more than half-way. If pulled less than half-way, the
driver will run in the normal impacting mode. When
using the mode, the tool will shut off automatically
once the screw is fully seated.
Using the Control Switch
The control switch may be set to three posi-
tions: forward, reverse and lock. Due to a lock-
out mechanism, the control switch can only
be adjusted when the ON/OFF switch is not
pressed. Always allow the motor to come to a
complete stop before using the control switch.
Drive Control Button
Tapping Screw Mode
to cycle through
2 3
Designed for
driving
self-tapping
screws
in sheet metal
Push for
Forward
1. For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
WARNING
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1. To start the tool, pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To vary the driving speed, increase or decrease
Speed
pressure on the trigger. The further the trigger is
Indicator
pulled, the greater the speed.
3. To stop the tool, release the trigger.
To protect the battery from damage and extend its
life, the tool's intelligent circuit monitors current draw,
temperature, and voltage drops.
In extremely high torque, binding, stalling, and short
circuit situations that cause high current draw, the
fuel gauge will flash, and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal tem-
perature of the battery could become too high. If this
happens, the fuel gauge will flash and the battery
pack will shut off. Let the battery pack cool and then
continue work.
WARNING
and wires before drilling or driving screws.
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight, reduce the impacting time. If they are
not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the
head of the fastener affects the degree of tightness.
The torque required to loosen a fastener averages
75% to 80% of the tightening torque, depending on
the condition of the contacting surfaces.
4
PUSH TO CENTER TO LOCK
To reduce the risk of injury, always
hold or brace securely.
Battery Pack Protection

APPLICATIONS

To reduce the risk of electric shock,
check work area for hidden pipes

Impacting Techniques

Push for
Reverse