Euromate SFC-25 Manuel Opérateur page 10

1 PREFACE
Using this manual
This manual is intended to be used as a work of reference for professional,
well trained and authorised users to be able to safely install, use, maintain
and repair the product mentioned on the cover of this document. The
figures referred to in the text, can be found in the back of this manual.
Pictograms and symbols
The following pictograms and symbols are used on the product and in this
manual.
WARNING
Denotes risk of electric shock.
WARNING
Wait after switching off the motor until the fan has stopped
before dismounting the filters.
Suggestions and recommendations to simplify carrying out
tasks and actions.
WARNING
Procedures, if not carried out with the necessary caution may
damage the product or cause personal injury.
WARNING
Fire hazard! Never use the product for extracting and/or filtering
inflammable, glowing or burning particles or solids or liquids.
Never use the product for extracting and/or filtering of
aggressive fumes (such as hydrochloric acid) or sharp particles.
Service and technical support
For information about specific adjustments, maintenance or repair jobs
which are not dealt with in this manual, please contact the supplier of the
product. He will always be willing to help you. Make sure you
have the following specifications at hand:
- product name
- serial number
These data can be found on the identification plate.
2 IDENTIFICATION OF THE PRODUCT
The identification plate (fig. 1) contains the following data:
A serial number
B product name
C power
D supply voltage and frequency
3 SAFETY INSTRUCTIONS AND WARNINGS
General
The manufacturer does not accept any liability for damage to the product or
personal injury caused by non-observance of the safety instructions in this
manual, or by negligence during installation, use, maintenance and repair of
the product mentioned on the cover of this document and any
corresponding accessories. Specific working conditions or used accessories
may require additional safety instructions. Immediately contact your supplier
if you detect a potential danger when using the product.
The user of the product is always fully responsible for observing the local
safety instructions and regulations. Observe all applicable safety instructions
and regulations.
10
User manual
• Everyone working on or with the product, must be familiar with the
contents of this manual and must strictly observe the instructions
therein. The management should instruct the personnel in accordance
with the manual and observe all instructions and directions given.
• Never change the order of the steps to perform.
• Always keep the manual with the product.
Pictograms and instructions on the product
• The pictograms, warnings and instructions attached to the product are
part of the safety features. They must not be covered or removed and
must be present and legible during the entire life of the product.
• Immediately replace or repair damaged or illegible pictograms,
warnings and instructions.
Users
• The use of this product is exclusively reserved to authorised, trained
and qualified users. Temporary personnel and trainees can only use the
product under supervision and responsibility of skilled engineers.
• The device is not intended to be used by persons (including children)
with physical, sensory or mental disability, or without the necessary
experience and knowledge unless they are supervised or instructed on
how the device can be used by one person who is responsible for their
safety.
• Always supervise children to prevent them playing with the appliance.
Intended use
1
The product is designed solely for the extraction and / or filter harmful fumes
and dusts (SFM / HFM) and gases (SFC / HFC) which are released during the
most common industrial processes and for use in commercial kitchens.
Using the product for other purposes is considered contrary to its intended
use. The manufacturer accepts no liability for any damage or injury resulting
from such use. The product has been built in accordance with state-ofthe-art
standards and recognised safety regulations. Only use the product in
technically perfect condition with its intended use and the instructions laid
down in the user manual.
Safety features
• All safety features must be correctly mounted and can only be removed
for maintenance and repair jobs by skilled and authorised service
engineers.
• The product must not be used if the safety features are not or only
partly present, or defective.
• The safety features should be regularly checked for their proper
functioning, and if required, be immediately repaired.
Modifications
• Modification of (parts of ) the product is not allowed.
1. "Intended use" as laid down in EN-292-1 is the use for which the technical product is suited as
specified by the manufacturer, inclusive of his directions in the sales brochure. In case of doubt it is
the use which can be deducted from the construction, the modeland the function of the technical
product which is considered normal use. Operating the machine within the limits of its intended
use also involves observing the instructions in the user manual.