Hoover WINDTUNNEL All-Terrain Serie Guide D'utilisation page 3

MAINTENANCE
2
Tap the filter on trash can and wipe away
remaining dust with a dry cloth. Place exhaust
filter back onto the vacuum.
CLEANING THE RINSABLE FILTER
PART #440015878
1
Remove the dirt cup, then remove the filter from
the dirt cup lid.
TROUBLESHOOTING
FIND AVAILABLE REPLACEMENT PARTS AND ACCESSORIES AT HOOVER.COM
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE.
ALWAYS IDENTIFY YOUR CLEANER BY THE COMPLETE MODEL NUMBER. (THE MODEL NUMBER APPEARS ON THE BACK OF THE CLEANER.)
PROBLEM POSSIBLE SOLUTION
My vacuum will not turn ON 1. Always be sure to plug it in firmly.
2. The Thermal Protector may have been activated - unplug your vacuum, check for clogs and let cool for 30 minutes. If this does not work, there may be no
3. Check the fuse or breaker in your home. If there is a blown fuse or tripped breaker, replace the fuse in your home or reset the breaker.
My vacuum is hard to push 1. Adjust to low mode by pressing the mode button.
2. Slide open the valve on the nozzle.
My vacuum is losing suction and/ 1. Be sure to empty the dirt cup if it is full. Check that the dirt cup is properly assembled and installed onto the appliance.
or not picking up
2. You may have a clogged filter or a clog in the system. Refer to the Maintenance section in this manual for directions on removing clogs.
3. Your filter may be dirty. Pre-motor filters should be rinsed every 2-3 months. Refer to the Maintenance section for directions on how to clean filters.
4. Adjust the mode for appropriate floor type.
My brushroll is not spinning 1. Unplug and remove any hair or other blockages around the brushroll.
2. Resume normal operation.
HOOVER WINDTUNNEL ALL-TERRAIN
®
Look for these accessories on Hoover.com or call 1-800-944-9200
ATTACHMENTS
Turbo Tool
2-in-1 Dusting Brush
Dusting Brush
Crevice Tool
LED Crevice Tool
Additional Filter
2
Rinse filter with water only until the filter is
clean and the water runs through clear. Gently
squeeze the filter to remove excess water.
24-48
HRS
3
Allow the filter to air dry for at least 24 hours.
IMPORTANT: The filter must be completely dry
before replacing it. This may take between 24
and 48 hours.
Check the inside of filter for dampness before
replacing.
voltage in the wall plug.
UPRIGHT ACCESSORY LIST
™
PART #
440015876
440015873
440010872
440015874
440015875
440015877
REMOVING SYSTEM CLOGS
If you are experiencing a loss of suction, or you
notice debris is spitting out of the nozzle, we
recommend checking the nozzle, tube, hose
and filters for any visible signs of blockage
or built up debris. It is also recommended to
rinse your Filter if there is visible built up dirt
and dust on the filter. This should help improve
performance on your vacuum.
TIP
Vacuum is equipped with an automatic
brushroll shutoff in the event of overload
or jam. Check for obstructions in the brush
roll area and remove any obstructions.
When obstructions are cleared, resume
cleaning as normal.
WARNING:
To reduce the risk of personal injury, unplug before cleaning or servicing.
ASSOCIATED MODELS
UH77200V, UH77210V
UH77200V
UH77210V
UH77210V
UH77200V
UH77200V
THERMAL PROTECTION
A thermal protector has been designed into
your cleaner to protect it from overheating.
When the thermal protector activates the
cleaner will stop running.
If this happens proceed as follows:
1. Turn cleaner OFF and unplug it.
2. Empty the dirt cup
3. Inspect the nozzle inlet, hose connector,
hose, dirt cup inlet, cyclonic filter
rinsable filter and exhaust filter for any
obstructions. Clear obstructions if present.
4. When cleaner is de-energized and motor
cools for 30 minutes, the thermal
protector will deactivate and cleaning
may continue.
If the thermal protector continues to acti-
vate after following the above steps, your
cleaner needs servicing.