Kärcher RCV 5 Mode D'emploi page 19

● Contact details for the KÄRCHER Service Centres
Connecting the cleaning robot with the Kärcher
Home Robots App and WLAN:
1. Download the KÄRCHER Home&Garden App from
the Apple App Store or from the Google Play Store.
2. Open the Kärcher Home Robots App.
3. Create an account (if you are not already regis-
tered).
4. Add the desired cleaning robot.
5. Follow the step-by-step instructions in the App.
Initial startup
Installing the dust container
For dry cleaning, remove the wiper cloth and the wiper
cloth holder, see chapter Removing the wiper cloth
holder.
Illustration E
1. Open the cover at the top.
2. Press the dust container into position until it audibly
latches into place.
3. Close the cover at the top.
Removing the dust container
Illustration F
1. Open the cover at the top.
2. Press the clamp.
3. Remove the dust container.
Installing the water reservoir
The water reservoir may contain a small amount of re-
sidual water due to quality control. This is normal.
Illustration G
1. Push the water reservoir horizontally into the clean-
ing robot until it audibly latches into place.
Removing the water reservoir
1. Press any button.
The cleaning robot stops.
2. Remove the water reservoir.
Illustration H
a Press the lock button down.
b Pull the water reservoir horizontally out of the
cleaning robot.
Installing the wiper cloth
1. Insert the wiper cloth into the slot of the wiper cloth
holder and fix it to the Velcro fastener.
Illustration I
Removing the wiper cloth
1. Press any button.
The cleaning robot stops.
2. Pull the wiper cloth off the Velcro fastener of the wip-
er cloth holder.
Illustration J
Installing the wiper cloth holder
1. Install the wiper cloth holder.
Illustration K
a Press the clamps together.
b Push the wiper cloth holder horizontally into the
cleaning robot until it audibly latches into place.
Removing the wiper cloth holder
1. Press any button.
The cleaning robot stops.
2. Remove the wiper cloth holder.
Illustration L
a Press the clamps together.
b Remove the wiper cloth holder.
Reset WLAN connection
If you switch to a new router or change your WLAN
password, you must reset the cleaning robot's WLAN
connection.
Note
Only 2.4 GHz WLAN networks are supported.
1. Switch on the cleaning robot, see chapter Switching
on the cleaning robot.
2. Press the On/Off button and the "Return to charging
station" button simultaneously for 7 seconds until a
voice says: "Resetting the WLAN connection and
entering network configuration mode".
3. Connect the cleaning robot to the charging station,
see chapter Connecting the cleaning robot with the
charging station.
Restoring the factory settings
 Press and hold the reset button for 3 seconds.
The factory settings are restored
The latest version of the firmware is installed.
 Press and hold the reset button for 10 seconds.
The factory settings are restored.
All network connection information, map informa-
tion, scheduled tasks and do-not-disturb informa-
tion, and customisation information are deleted.
The suction performance is reset to the default val-
ue.
Setting up cleaning zones
The cleaning robot only cleans within the selected area.
Cleaning zones can only be set up with the App. Down-
loading the App is described in the chapter Connecting
cleaning robots with WLAN and App.
 Follow the step-by-step instructions in the App.
Setting up virtual walls
Virtual walls and restricted areas prevent the cleaning
robot from entering areas that should not be cleaned.
Virtual walls can only be set up with the App. Download-
ing the App is described in the chapter Connecting
cleaning robots with WLAN and App.
 Follow the step-by-step instructions in the App.
Activating mapping
The cleaning robot starts from the charging station and
automatically updates its map after completing a clean-
ing task and after charging.
Mapping can only be set up with the App. Downloading
the App is described in the chapter Connecting clean-
ing robots with WLAN and App.
Note
To avoid losing the map, wait a few seconds after the
first mapping until the map is saved.
 Follow the step-by-step instructions in the App.
ATTENTION
Damage due to moisture
Remove the wiper cloth with wiper cloth holder before
charging and when not in use, see chapter Removing
the wiper cloth holder.
Remove the water reservoir before charging and when
not in use, see chapter Removing the water reservoir.
Protect carpets using virtual walls, see chapter Setting
up virtual walls.
English
Operation
19