Makita 6207D Manuel D'instructions page 4

ENGLISH
1 Battery cartridge
2 Button
3 Switch trigger
4 Reversing switch lever
5 Clockwise
6 Counterclockwise
7 Speed change lever
SPECIFICATIONS
Model
Capacities
Steel .....................................10 mm
Wood ....................................25.4 mm
Wood screw..........................6 x 75 mm
Machine screw .....................13 mm
-1
No load speed (min )
High ......................................0 – 1,300
Low.......................................0 – 400
Overall length ............................233 mm
Net weight .................................1.7 kg
Rated voltage ............................D.C.9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
4
Explanation of general view
8 Action mode change lever
9 Lock button
10 Adjusting ring
11 Graduations
12 Pointer
13 Sleeve
14 Ring
6207D 6217D
10 mm
25.4 mm
6 x 75 mm
13 mm
0 – 1,300
0 – 400
233 mm
1.9 kg
D.C.12 V
ENC004-1
15 Bit
16 Bit holder
17 Limit mark
18 Brush holder cap
19 Screwdriver
6317D
13 mm
25.4 mm
6 x 75 mm
13 mm
0 – 1,300
0 – 400
243 mm
2.0 kg
D.C.12 V
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
6337D 6347D
13 mm 13 mm
32 mm 38 mm
6 x 75 mm 10 x 89 mm
13 mm 13 mm
0 – 1,300 0 – 1,300
0 – 400 0 – 400
243 mm 243 mm
2.1 kg 2.4 kg
D.C.14.4 V D.C.18 V