KitchenAid KBFN502ESS Guide D'utilisation Et D'entretien page 17

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction
NSF
Aesthetic Effects
Reduction
Requirements
Chlorine Taste/Odor
50% reduction
Particulate Class II*
85% reduction
Contaminant
NSF Reduction
Reduction
Requirements
Lead: @ pH 6.5 ***
0.010 mg/L
Lead: @ pH 8.5 ***
0.010 mg/L
Mercury: @ pH 6.5
0.002 mg/L
Mercury: @ pH 8.5
0.002 mg/L
Benzene
0.005 mg/L
O-Dichlorobenzene
0.6 mg/L
Toxaphene
0.003 mg/L
Carbofuran
0.040 mg/L
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
Use replacement filter T2RFWG2, part #4396841.
Model T1WG2L: Style 1 – When the filter indicator reads
10%, order a new filter. When the indicator reads 0%, it is
recommended that you replace the filter.
Style 2 – When the filter indicator changes from green to
yellow, order a new filter. When the indicator changes from
yellow to red, it is recommended that you replace the filter.
Style 3 – When the water filter status display changes from
"GOOD" to "ORDER," order a new filter. When the filter
indicator reads "REPLACE," it is recommended that you
replace the filter.
Style 4 – Press FILTER to check the status of your water filter.
If the filter indicator light is yellow, order a new filter. If the filter
indicator light is red, it is recommended that you replace the
filter.
Model T1WG2: Change the water filter cartridge every 6
months. If the water flow to the water dispenser or ice maker
decreases noticeably before 6 months have passed, replace
the water filter cartridge more often.
These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
*Class II particle size: 1 um to <5 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dus
***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.
NSF is a registered trademark of NSF International.
®
Base Grille Water Filtration System
Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)
Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)
System tested and certified by NSF International against NSF/ANSI Standard 42 for
the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI
Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene,
and Carbofuran.
Average
Influent Challenge
Influent
Concentration
2.0182 mg/L
2.0 mg/L ± 10%
1333333 #/mL
At least
10,000 particles/mL
Average
Influent Challenge
Influent
Concentration
0.1533 mg/L
0.15 mg/L ± 10%
0.1400 mg/L
0.15 mg/L ± 10%
0.0058 mg/L
0.006 mg/L ± 10%
0.0059 mg/L
0.006 mg/L ± 10%
0.0154 mg/L
0.015 mg/L ± 10%
1.7571 mg/L
1.8 mg/L ± 10%
0.015 mg/L
0.015 mg/L ± 10%
0.0819 mg/L
0.08 mg/L ± 10%
Maximum
Average
Effluent
Effluent
0.06 mg/L
0.0536 mg/L
6600 #/mL**
2325 #/mL
Maximum
Average
Effluent
Effluent
0.0005 mg/L
0.0005 mg/L
0.0007 mg/L
0.0006 mg/L
0.0002 mg/L
0.0002 mg/L
0.0005 mg/L
0.0003 mg/L
0.0012 mg/L
0.0006 mg/L
0.0250 mg/L
0.0066 mg/L
0.001 mg/L
0.001 mg/L
0.0400 mg/L
0.0213 mg/
The product is for cold water use only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.
Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.
Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply
Water Pressure
Water Temperature
Service Flow Rate
Minimum%
Average%
Reduction
Reduction
97.03%
97.34%
99.51%
99.83%
Minimum%
Average%
Reduction
Reduction
99.67%
99.67%
99.50%
99.57%
96.54%
96.54%
91.57%
94.92%
92.22%
96.34%
98.58%
99.63%
93.3%
93.3%
51.13%
74.00%
City or Well
35 - 120 psi (241 - 827 kPa)
33° - 100°F (1° - 38°C)
0.5 gpm (1.9 L/min.) @ 60 psi*
17

Publicité

Table des Matières
loading

Table des Matières