EINHELL AXXIO 36/230 Q Mode D'emploi page 13

Additional Safety Warnings Specifi c for
Abrasive cut-off Operations:
a) Do not jam the cut-off wheel or apply
excessive pressure. Do not attempt
to make an excessive depth of cut.
Overstressing the wheel increases the
loading and susceptibility to twisting or
binding of the wheel in the cut and the
possibility of kickback or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your body, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when
interrupting a cut for any reason, switch
off the power tool and hold the power tool
motionless until the wheel comes to a
complete stop. Never attempt to remove
the cut-off wheel from the cut while the
wheel is in motion otherwise kickback
may occur. Investigate and take corrective
action to eliminate the cause of wheel
binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully reenter the cut. The wheel
may bind, walk up or kickback if the power
tool is restarted in the workpiece.
e) Support panels or any oversized
workpiece to minimize the risk of
wheel pinching and kickback. Large
workpieces tend to sag under their own
weight. Supports must be placed under the
workpiece near the line of cut and near the
edge of the workpiece on both sides of the
wheel.
f) Use extra caution when making a "pocket
cut" into existing walls or other blind
areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that
can cause kickback.
g) Do not attempt to do curved cutting.
Overstressing the wheel increases the
loading and susceptibility to twisting or
binding of the wheel in the cut and the
possibility of kickback or wheel breakage,
which can lead to serious injury.
h) When using a Type A (cut-off ) wheel guard
for facial grinding, the wheel guard may
interfere with the workpiece causing poor
control.
i) When using a Type B (grinding) wheel
guard for cutting-off operations with bonded
Anl_Axxio_36_230_Q_SPK7_USA.indb 13 Anl_Axxio_36_230_Q_SPK7_USA.indb 13
EN
abrasive wheels, there is an increased risk of
exposure to emitted sparks and particles, as
well as exposure to wheel fragments in the
event of wheel burst.
j ) When using a Type A (cut-off ), Type B
(grinding) or Type C (combination) wheel
guard for cutting-off and facial operations in
concrete or masonry, there is an increased
risk of exposure to dust and loss of control
resulting in kickback.
k) When using a Type A (cut-off ), Type B
(grinding) or Type C (combination) wheel
guard with a wheel-type wire brush with
a thickness greater than the maximum
thickness, the wires may catch on the guard
leading to breaking of wires.
SAVE THESE INSTRUCTIONS
2. Layout and items supplied
2.1 Layout
1. Spindle lock
2. On/Off switch
3. Additional handle
4. Guard
5. Face spanner
6. Clamping fl ange
7. Flange nut
8. Quick-clamp nut
9. Clamp lever
10. Handle
11. Locking button
12. Lock lever
13. Battery capacity indicator button
14. Battery capacity indicator
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.
•
Open the packaging and take out the
equipment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
present).
•
Check to see if all the items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, keep the packaging until the end
- 13 -
14.07.2023 09:24:36 14.07.2023 09:24:36