Makita 6319D Manuel D'instructions page 4

ENGLISH
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Speed change lever
6 Action mode change lever
7 Arrow
SPECIFICATIONS
Model
Capacities
Steel ..................................................... 13 mm
Wood .................................................... 45 mm
Wood screw.......................................... 6 mm x 75 mm
Machine screw ..................................... 6 mm
-1
No load speed (min )
High (3)................................................. 0 – 1,600
Medium (2) ........................................... 0 – 550
Low (1) ................................................. 0 – 300
Overall length .......................................... 246 mm
Net weight ............................................... 2.2 kg
Rated voltage .......................................... D. C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES FOR POWER
TOOL
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
4
Explanation of general view
8 Adjusting ring
9 Graduations
10 Steel band
11 Grip base
12 Side grip
13 Sleeve
14 Bit
6319D
8.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1.
GEB001-1
2.
3.
4.
5.
6.
7.
15 Bit holder
16 Depth rod
17 Clamp screw
18 Limit mark
19 Brush holder cap
20 Screwdriver
6339D
13 mm
50 mm
6 mm x 75 mm
6 mm
0 – 1,700
0 – 600
0 – 300
246 mm
2.3 kg
D. C. 14.4 V
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
6349D
13 mm
65 mm
10 mm x 89 mm
6 mm
0 – 1,700
0 – 600
0 – 300
246 mm
2.6 kg
D. C. 18 V
ENC004-1