Publicité
Les langues disponibles
Les langues disponibles
special adjustment mechanism.
NOTE!
If you need to adjust the inner padding and/or shoulder
straps, ensure that the TAKATA MIDI I-SIZE has
approximately the same orientation as it would have
when installed in the vehicle.
WARNING!
[MIDI_I-SIZE_048] Always ensure that the AIRPADS
are positioned correctly in the inner pockets of the
adjustable inner padding and in the space provided in
the lateral crash pads under the basic cushion. Failure
to observe this notice may seriously risk your child's
safety in the event of an accident.
Step 1 – Unlock the adjustable inner padding
[MIDI_I-SIZE_019] Open the compartment for the
manual on the backside of the TAKATA MIDI I-SIZE.
[MIDI_I-SIZE_020] Fully depress the slider to adjust
the inner padding on the back of the TAKATA MIDI
I-SIZE.
Step 2 – Adjust and fasten the inner padding
Keep the slider pressed down, and at the same time,
slide the inner padding up or down, to adjust this and
the shoulder straps to the size of your child. Then
release the slider again. The slider is locked in place
when the metal arm clicks into the slots on each side.
CAUTION!
Whenever you adjust the seat, check that the slider is
locked into position again. To do this, gently try to
move the slider up or down, without pushing it in.
It may be necessary to adjust the inner padding
further, according to your child's size. For further
information on this, please see Section 5 – Securing
your child (Step 1 – Adjusting and fastening the inner
padding and strap).
Loosening the straps and opening the buckle
Before placing your child in the TAKATA MIDI
I-SIZE or removing your child from it, loosen the
straps and open the buckle. The TAKATA MIDI
I-SIZE features a central lever that is used to loosen
the straps.
Step 1 – Unblock the straps
[MIDI_I-SIZE_021] To loosen the straps, pull the
lever up and hold it in this position.
All manuals and user guides at all-guides.com
Step 2 – Loosen straps
At the same time, pull the shoulder straps gently
forward as far as possible.
Step 3 – Open the buckle
[MIDI_I-SIZE_022] To open the buckle, press the red
button on it, and remove the tongues.
The two tongues are held together magnetically, and
can be easily separated by pulling them apart.
Adjusting the seat inclination
[MIDI_I-SIZE_023 + MIDI_I-SIZE_024] The
inclination of the forward facing TAKATA MIDI
I-SIZE can be adjusted by pressing the seat inclination
lever below the front end of the shell upwards. Keep
the seat inclination lever pressed, and at the same
time, pivot the shell up or down at the front end. Then
release the seat inclination lever again so that the seat
shell is locked in upper or lower position. This is
indicated by a click.
CAUTION!
Whenever you adjust the seat inclination, check that
the seat shell and lever are locked into position again.
To do this, gently try to move the front end of the shell
up or down, without pressing the inclination lever.
NOTE!
The inclination of the seat can only be adjusted when
installing the TAKATA MIDI I-SIZE forward facing
on the TAKATA I-SIZE BASE.
If it is not possible to install the TAKATA MIDI
I-SIZE rearward facing on the TAKATA I-SIZE
BASE, please kindly check the position of the
inclination. If necessary, change the inclination and
install the TAKATA MIDI I-SIZE rearward facing on
the TAKATA I-SIZE BASE again.
TAKATA I-SIZE BASE
Adjusting the support leg
Step 1 – Fold out the support leg
[MIDI_I-SIZE_025 + MIDI_I-SIZE_026] Take hold
of the support leg on the underside of the TAKATA
I-SIZE BASE. Push the release slider of the folding
mechanism to the side, pull the support leg out of the
transportation position, and swing it out as far as it
will go. When it reaches full extension, the support leg
is locked into place by a spring in the release slider.
de
en
fr
it
es
nl
21
Publicité
