Publicité
Les langues disponibles
Les langues disponibles
Installing or removing depressed
center wheel or flap disc
Optional accessory
WARNING:
When using a depressed center
wheel or flap disc, the wheel guard must be fitted
on the tool so that the closed side of the guard
always points toward the operator.
WARNING:
Make sure that the mounting part
of the inner flange fits into the inner diameter of
the depressed center wheel / flap disc perfectly.
Mounting the inner flange on the wrong side may
r e s u l t i n t h e d a n g e r o u s v i b r a t i o n .
Mount the inner flange onto the spindle.
Make sure to fit the dented part of the inner flange onto
t h e s t r a i g h t p a r t a t t h e b o t t o m
Fit the depressed center wheel / flap disc on the inner
flange and screw the lock nut onto the spindle.
Fig.10: 1. L o c k n u t 2. D e p r e s s e d c e n t e r w h e e l
3. Inner flange 4. M o u n t i n g p a r t
To tighten the lock nut, press the shaft lock firmly so
t h a t t h e s p i n d l e c a n n o t r e v o l v e , t h e n u s e t h e l o c k n u t
wrench and securely tighten clockwise.
Fig.11: 1. L o c k n u t w r e n c h 2. S h a f t l o c k
T o r e m o v e t h e w h e e l , f o l l o w t h e i n s t a l l a t i o n p r o c e d u r e
i n r e v e r s e .
Installing or removing flex wheel
Optional accessory
WARNING:
Always use supplied guard when
flex wheel is on the tool. W h e e l c a n s h a t t e r d u r i n g
u s e a n d g u a r d h e l p s t o r e d u c e c h a n c e s o f p e r s o n a l
injury.
Fig.12: 1. L o c k n u t 2. F l e x w h e e l 3. B a c k u p p a d
4. Inner flange
F o l l o w i n s t r u c t i o n s f o r d e p r e s s e d c e n t e r w h e e l b u t a l s o
u s e b a c k u p p a d o v e r w h e e l .
Installing or removing abrasive disc
Optional accessory
Fig.13: 1. S a n d i n g l o c k n u t 2. A b r a s i v e d i s c
3. Rubber pad
1.
M o u n t t h e r u b b e r p a d o n t o t h e s p i n d l e .
2.
F i t t h e d i s c o n t h e r u b b e r p a d a n d s c r e w t h e s a n d -
i n g l o c k n u t o n t o t h e s p i n d l e .
3.
Hold the spindle with the shaft lock, and securely
t i g h t e n t h e s a n d i n g l o c k n u t c l o c k w i s e w i t h t h e l o c k n u t
w r e n c h .
T o r e m o v e t h e d i s c , f o l l o w t h e i n s t a l l a t i o n p r o c e d u r e i n
r e v e r s e .
NOTE: Use sander accessories specified in this man-
ual. These must be purchased separately.
o f t h e s p i n d l e .
Super flange
Optional accessory
Only for model GA4595 / GA5095
Super flange is a special accessory for model which is
N O T e q u i p p e d w i t h a b r a k e f u n c t i o n .
Only 1/ of e orts needed to undo lock nut, compared
with conventional type.
Installing or removing Ezynut
Optional accessory
Only for tools with M14 spindle thread.
CAUTION:
Do not use Ezynut with Super
Flange. Those flanges are so thick that the entire
thread cannot be retained by the spindle.
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
Fig.14: 1. Ezynut 2. A b r a s i v e w h e e l 3. Inner flange
4. S p i n d l e
Press shaft lock firmly and tighten Ezynut by turning the
a b r a s i v e w h e e l c l o c k w i s e a s f a r a s i t t u r n s .
Fig.15: 1. S h a f t l o c k
To loosen the Ezynut, turn the outside ring of Ezynut
c o u n t e r c l o c k w i s e .
NOTE: Ezynut can be loosened by hand as long
a s t h e a r r o w p o i n t s t h e n o t c h . O t h e r w i s e a l o c k n u t
w r e n c h i s r e q u i r e d t o l o o s e n i t . I n s e r t o n e p i n o f t h e
wrench into a hole and turn Ezynut counterclockwise.
Fig.16: 1. A r r o w 2. N o t c h
Fig.17
Installing abrasive cut-off / diamond
wheel
Optional accessory
WARNING:
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
WARNING:
grinding.
Fig.18: 1. L o c k n u t 2. Abrasive cut-o wheel / dia-
m o n d w h e e l 3. Inner flange 4. W h e e l g u a r d
for abrasive cut-o wheel / diamond wheel
A s f o r t h e i n s t a l l a t i o n , f o l l o w t h e i n s t r u c t i o n s f o r
d e p r e s s e d c e n t e r w h e e l .
T h e d i r e c t i o n f o r m o u n t i n g t h e l o c k n u t a n d t h e i n n e r
flange varies by wheel type and thickness.
Refer to the following figures.
When installing the abrasive cut-off wheel:
Fig.19: 1. L o c k n u t 2. Abrasive cut-o wheel
(Thinner than
o wheel ( mm (5/
flange
When installing the diamond wheel:
Fig.20: 1. L o c k n u t 2. Diamond wheel (Thinner than
mm (5/
(5/
15 ENGLISH
When using an abrasive cut-off
NEVER use cut-off wheel for side
)) 3. A b r a s i v e c u t -
mm (5/
) or thicker) 4. I n n e r
)) 3. Diamond wheel ( mm
) or thicker) 4. Inner flange
Publicité
