Analogue Recording From An External Source - Philips CDR 765 Mode D'emploi

RECORDING
• To check the (remaining) recording time, press DISPLAY.
(This can also be done during recording)
3 To stop recording, press STOP on the CD Recorder/Player.
- and go out.
CD SYNC RECORD
• To interrupt recording, press PAUSE.
starts to flash. To resume, press PLAY on the
RECORD
CD Recorder/Player.
After recording the display will show UPDATE for several
seconds.
Note:
- The CD Recorder/Player will not start until it recognizes
a digital signal. Although the reaction time is less than
200 milliseconds, the very beginning of the music may
sometimes not be recorded. If this happens, you can start
the recording manually (see digital recording -
unsynchronized).
- Recordings from DAT or DCC will only stop after 20 seconds
silence.

Analogue recording from an external source

RE CO RD
CD SY N
TR AC K
C
DU BB 1
OV ER
SC AN
TO TA L
RE M
TI M E
PA US E
DI G
CD
RE W RI TA RE PE AT
1
BL E
C O M
P A C T
D I S C
D IS P LA
R E C O
Y
S O U R C
E
R E C LE V
E L
Only make analog recordings if digital recording is not
possible.
Preparing for analogue recording
1 Make sure the disc is absolutely free of scratches and
dust particles.
2 Press SOURCE repeatedly until:
appears on the display.
ANALOG
FINALIZE CD SYNC
SHUFFLE SCAN
DUBB 1
AUTO TRACK TOTAL REM TRACK TIME
ANALOG OPT PROG
PAUSE DIG REPEAT 1
• If necessary, press DUAL to switch off the
will no longer appear on the display.
D D U U A A L L
TRACK
RECORD ERASE
FINALIZE CD SYNC
SHUFFLE SCAN
DUBB 1
AUTO TRACK TOTAL REM TRACK TIME
16
TR AC K
TO TA L
RE M
TI M E
PA US E
RE PE AT
1
R D E R
C D R 7
6 5
D U A L
D IS P LA
Y
P H O N E
S
SRC
SHUFFLE
TOTAL REM TRACK TIME
PAUSE PROG
REPEAT 1
mode;
D D U U A A L L
OVER TRACK
DUAL
SRC
SHUFFLE
TOTAL REM TRACK TIME
3 Press AUTO/MANUAL to switch between auto and manual
track numbering.
If Auto is selected (preferred),
the display.
• AUTO: The track number is automatically incremented after
a silence on the original of at least 3 seconds.
• MANUAL: Track numbers can be incremented manually by
pressing §. (minimum track length is 4 seconds.)
(This can also be done in AUTO mode)
• Track numbers cannot be changed after recording.
4 With the recorder stopped, press RECORD to enter Record
standby mode.
will flash
RECORD
TRACK
RECORD ERASE
CD SYNC
FINALIZE
SHUFFLE SCAN
DUBB 1
AUTO TRACK TOTAL REM TRACK TIME
5 Play the source first to set the optimal recording level on
the CD Recorder/Player.
6 Press REC LEVEL (+ or -) repeatedly until all the blue
segments on the Record/Play level bar light up continuously
but the red segments do not during the loudest passages.
The display will show -3DB or 0DB or 3DB or 6DB
7 Stop the source.
Start analogue recording
1 To start recording, press PLAY on the CD Recorder/Player
and immediately start the source.
lights continuously.The track number and
RECORD
recording time used appear on the display.
• To record a 3-second silence at the start of a track,
press PAUSE.
• To check the (remaining) recording time, press DISPLAY.
(This can also be done during the recording)
2 To stop recording, press STOP on the CD Recorder/Player.
will go out.
RECORD
• To interrupt recording, press PAUSE.
will start to flash. Resume at step 1.
RECORD
After recording the display will show UPDATE for several
seconds.
Note: With on, the recorder will stop
AUTO TRACK
automatically after a 20 seconds silence.
With off, the
AUTO TRACK
appears on
AUTO TRACK
OVER TRACK
DUAL
SRC
SHUFFLE
TOTAL REM TRACK TIME
mode is disabled.
AUTO STOP