Publicité
Les langues disponibles
Les langues disponibles
Service Indicator LED (Fig. A)
Your breaker has an LED service indicator. Refer to the table for
more information on LED functionality.
lED Function
Yellow
(permanently on)
D
WALT Tool Tag Ready (Fig. A)
e
Optional Accessory
Your tool comes with tool tag mounting holes
fasteners
for installing a D
12
T15 bit tip to install the tag.
WARNING: Use only original fasteners. Longer screws
increase the risk of electrical shock or damage to the tool.
The D
WALT Tool Tag is designed for tracking and locating
e
professional power tools, equipment, and machines using
the D
WALT Tool Connect™ app. For proper installation of the
e
D
WALT Tool Tag refer to the D
e
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Proper Hand Position (Fig. A, E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the main handle
Performing an Application (Fig. A, B)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly.
nOTE: Operating temperature of this tool is 7 to 40˚ C. Using
the tool outside of this temperature range will decrease the life
of the tool.
1. Insert the appropriate chisel and rotate it by hand to lock it
into the desired position. Refer to Bit and Tool Holder.
Description
service required
The yellow service indicator
LED
lights up to indicate
4
the tool needs servicing
within the next 8 hours of
use (brushes, lubrication and
hammer mechanism sealing).
9
and
WALT Tool Tag. You will need a
e
WALT Tool Tag manual.
e
5
.
2. Adjust the side handle
the Side Handle Assembly.
3. Place the chisel on the desired location.
4. Turn on the breaker by pushing down on the ON/OFF
switch
1
on the side marked "1".
5. To turn off the breaker, push down on the ON/OFF switch
on the side marked "0".
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
before cleaning.
WARNING: To ensure safe and efficient operation,
always keep the electrical appliance and the ventilation
slots clean.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Ventilation slots can be cleaned using a dry, soft non-metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
approved dust mask.
Optional Accessories
WARNING: Since accessories, other than those offered
2
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Various types of SDS max® chisels are available as an option.
Accessories and attachments used must be regularly lubricated
around the SDS max® fitment.
Chiselling dust extraction system DWH051. Can be used with all
D
WALT SDS max® chiselling hammers/breakers as well as 19
E
mm HEX chiselling hammers/breakers for dust-free chiselling.
Consult your dealer for further information on the
appropriate accessories.
as necessary. Refer to Mounting
2
WALT recommended
e
English
7
Publicité
