Publicité
Les langues disponibles
Les langues disponibles
Keep the power cord away from the bit. Do not wrap the
•
cord around any part of your body, this may cause personal
injury by loss of control. Damage supply cords could cause
electrical shock.
Make sure that there are no power or gas lines in the
•
work area. Damage to hidden power or gas lines can result in
injury from electric shock or explosion.
When working above the floor, make sure that the area
•
below is clear. Falling parts can cause injuries to bystanders.
In cold weather or if the unit has not been used for a
•
long time, run the unit without load for a few minutes
before use. High load in cold conditions may cause damage
to the breaker.
Make sure that the chisel is secured before using the
•
tool. Ejected parts can cause injuries.
Reducing Dust Exposure
Before starting work, check the hazard class of the dust that will
be produced when working.
WARNING: Avoid touching or breathing dust as it can
be harmful to health. Dust created when using a power
tool and when conducting other construction activities
can contain chemicals, minerals, or particles known to
cause respiratory infections, allergic reactions, cancer,
birth defects, or other reproductive harm of the user
or bystanders.
•
Such dust can be generated, for example, when working on
hardwoods such as beech or oak, lead‑based paint, concrete,
masonry, or stones containing quartz.
•
Material containing asbestos may be handled only
by specialists.
•
Observe the relevant regulations in your country for the
materials to be worked on.
•
Use a dust extractor or extraction system with an officially
approved protection class in compliance with the locally
applicable dust protection regulations and suitable for the
material to be worked on.
•
Capture the resulting dust particles directly at the source and
avoid deposits in the surrounding area. Use suitable extraction
accessories for this purpose.
Additional measures:
ʵ Make sure that the workplace is well ventilated.
ʵ Wear a respirator appropriate for the type of
dust generated.
Residual Risks
The following risks are inherent to the use of hammers:
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of squeezing fingers when changing the accessory.
•
Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
i
on the rating plate.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
WARNING: 127V units have to be operated via a fail‑safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(Middle East and Africa)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data). The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Breaker
1 Side handle
1 Instruction manual
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
English
WALT
e
; the
2
5
Publicité
