Publicité
Les langues disponibles
Les langues disponibles
Configuring your antenna
LNB POWER
•
V / H ----- Vertical 14V and Horizontal 18V for voltage switching type.
•
14V Skew On ----- 14V Low band for mechanical polarizer type.
•
18V Skew On ----- 18V High band for mechanical polarizer type.
•
Off ------ No power output.
Antenna: Press VOL up / down to select a reference number for each antenna you are using.
LNB Type: Press VOL up / down to select the type of LNB you are using. After selecting, press OK to configure the LO settings
if different from above.
LNB Power: Press VOL up / down to select the power output to your LNB.
22KHz Tone: When using other than Universal LNB, press VOL up / down to select tone status.
DiSEqC: If you are using more than one LNB for fixed installation using a DiSEqC switch, press VOL up / down to configure the
ports on the switch. See example below.
12V: If you want 12 volts output to control LNBs with a relay type switch, press VOL up / down to turn on 12 volts.
Please note that after making this setting, the 12 volts will turn on when channel search is activated.
STORE: Press OK to store the above settings.
EXAMPLE: SETTING DiSEqC SWITCH CONTROLS
To set the switch to four different satellites:
Antenna 1 For Astra 1, 19.2E, select
Antenna 2 For Astra 2, 28.2E, select
Antenna 3 For Hotbird 1-5 13E, select DiSEqC 3
Antenna 4 For Thor 2-3, 0.8W, select
Setting your DiSEqC antenna positioner
If you are using a DiSEqC 1.2 antenna positioner then you can search and download up to 20 satellites automatically using the
DiSEqC 1.3 menu. Further satellites can still be programmed individually. Follow steps below to do so.
East Limit: After entering furthest east limit, press OK and it will store the limit here.
West Limit: After entering furthest west limit, press OK and it will store the limit here.
Erase Limits: If you need to clear the limits, press OK and the limits will indicate 'None'.
Zero Position: If you need to move the antenna to 0 position as indicated on the DiSEqC positioner, press OK.
Re-sync: If you need to re/sync the positions, first find one satellite, then move down to 'Re-sync' and press OK.
STORE: Press OK to store the above settings.
All manuals and user guides at all-guides.com
INSTALL MENU: ANTENNA SETTINGS
By default your receiver is preset to UNIVERSAL LNB for all antenna numbers ( 1-
50 ). If you are using one antenna and one Universal LNB, then you do not need to
change any settings. However you can re-program these to your requirements when
using two or more LNBs and antennas.
LNB TYPE AND LOCAL OSCILLATOR (LO) SETTINGS
•
Universal --- Low 9750, High 10600, and 22KHz tone selection is automatic.
•
Single -------- 10750, 22KHz tone can be set on or off.
•
Single – S --- 5150, 22KHz tone can be set on or off.
•
Wide --------- Low 9750, High 10750, 22KHz tone can be set on or off.
You can change the LO figure for any of these settings to suit your LNB.
DiSEqC 1
DiSEqC 2
DiSEqC 4
INSTALL MENU: CHANNEL SEARCH
(With DiSEqC 1.2 positioner sub menu)
SETTING LIMITS Select CHANNEL SEARCH and move down to Positioner line.
Press VOL up / down and select DiSEqC 1.2, then press OK and set the East and
West limits.
MOVE: Press VOL up / down to move antenna furthest possible east or west limit,
then enter limits for each position.
INSTALL MENU: CHANNEL SEARCH
9
Publicité
