Télécharger Imprimer la page

Panasonic EY45A2LJ2G Instructions D'utilisation page 17

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 40
Collecting Dust
WARNING
* Before cutting metal materials, always empty
the dust case, open the front cover and
remove the dust.
• Use the tool with the flammable materials
in the dust case to cut metal materials may
result in fire.
* When cutting metal materials, always use the
tool with the dust case attached.
• Flying sparks and metal chips may cause
injury.
* When cutting metal materials, do not attach
a vacuum cleaner.
Sparks and hot metal chips may cause
the vacuum to be caught in fire. Operate
the vacuum cleaner in accordance with its
instructions.
(1) Collect dust in the dust case. [Fig.9]
* Empty the dust case when it is filled up with
dust.
* Empty the dust case before storing the tool.
* Dust case capacity
• When cutting electrical conduit with a
diameter of 25 mm (1"), approximately
130 cuts
• When cutting 45 mm (1-25/32") x 45 mm
(1-25/32") lumber, approximately 150 cuts
NOTE:
Some materials may cause dust to become
clogged inside the front cover when cutting
those materials.
(2) Use with vacuum cleaner to collect dust.
[Fig.10]
* Connect the tool to the hose using the
EY9X012E vacuum cleaner hose adapter
(sold separately).
Compatible hose inner diameter: 25 mm
(1") to 38 mm (1-2/1")
* Operate the vacuum cleaner obeying its
instructions.
NOTE:
When the tool has difficulty in ejecting or col-
lecting dust, the dust outlet may be clogged
with dust. Open the front cover and remove
any dust.
LED light [Fig.11]
LED light illuminates when the power switch is
depressed and turns off when the power switch
is released.
• The light illuminates with very low current, and it
does not adversely affect the performance of the
tool during use or its battery capacity.
CAUTION:
• The built-in LED light is designed to illuminate the
small work area temporarily.
• Do not use it as a substitute for a regular flashlight,
since it does not have enough brightness.
Caution : DO NOT STARE INTO BEAM.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
Control Panel
(1) Overheat warning lamp [Fig.12]
Indicates operation has been halted due to motor
or battery overheating.
The overheating protection feature halts tool
operation to protect the battery pack in the event
of overheating. The overheat warning lamp on the
control panel flashes when this feature is active.
• If the overheating protection feature activates,
allow the tool to cool thoroughly (at least 30
minutes). The tool is ready for use when the
overheat warning lamp goes out.
• Avoid using the tool in a way that causes the
overheating protection feature to activate
repeatedly.
• If the tool is used in cold-temperature condi-
tions (such as during winter) or if it is frequently
stopped during use, the overheating protection
feature may not activate.
The performance of the EY9L42 de-teriorates
significantly at and below 10 °C due to work
conditions and other factors.
• The ambient temperature range is between
0 °C (32 °F) and 40 °C (104 °F).
If the battery pack is used when the battery
temperature is below 0 °C (32 °F), the tool may
fail to function properly.
• When charging a cool battery pack (below 0 °C
(32 °F)) in a warm place, leave the battery
pack at the place and wait for more than one
hour to warm up the battery to the level of the
ambient temperature.
- 17 -
(1)
(2)
EN

Publicité

loading

Ce manuel est également adapté pour:

Ey45a2Ey45a2xmEy45a2xw