Télécharger Imprimer la page

Panasonic EY45A2LJ2G Instructions D'utilisation page 14

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 40
• Never use other than the dedicated charger
EN
to charge the battery pack. Otherwise, the
battery may leak, overheat, or explode.
• After removing the battery pack from the
tool or the charger, always reattach the pack
cover. Otherwise, the battery contacts could
be shorted, leading to a risk of fire.
• When the Battery Pack Has Deteriorated,
Replace It with a New One.
Continued use of a damaged battery pack
may result in heat generation, ignition or bat-
tery rupture.
III
. ASSEMBLY
Attaching or Removing Battery
Pack
CAUTION:
Before inserting battery pack, check that the
power switch in the tool actuates properly and
returns to the "OFF" position when released.
1. To attach the battery pack: [Fig.1]
Align the highlighted marker points and
attach battery pack.
Slide the battery pack until it locks into
position.
2. To remove the battery pack [Fig.2]
Push the button and slide the battery pack
forward.
IV
. OPERATION
Before Using the Tool
This tool is intended to cut unhardened fer rous
metal, nonferrous metal, wood, and plastic.
Refer to the "Accessories" section for a list of
blades to be used for the proper applications
of this tool. The following precautions must be
followed to reduce the risk of injury;
• Do not cut stacked materials. Cut one piece at
a time.
• Do not cut hardened steel.
• Cut materials with the wider edge of the shoe
over the clamped side of the material.
• Do not touch the saw blade, workpiece, or cut-
ting chips with bare hands immediately after
cutting; they may be hot and could burn skin.
Each time you use the tool, you must make sure
it is in good operating condition.
Use the following checklist:
1. Is the blade installed in the correct direction?
The arrow on the blade must point in the same
direction as the arrow on the upper blade
cover.
2. Is the blade installed properly?
Make sure the hex bolt is tightened securely.
[Fig.4]
3. Does the blade look alright?
Replace the blade immediately if there are
any cracks in it or if any teeth are broken.
4. Does the lower guard close properly?
WARNING
To avoid injury, do not use the tool if the lower
guard does not close quickly over the blade.
5. Is the transparent guard securely installed?
6. Is the battery pack charged and inserted
firmly to the tool?
7. Is the depth adjustment nut for cutting
securely tightened?
8. Is the workpiece securely clamped on a saw
horse or bench?
9. Is the dust case or front cover clogged with
dust?
10. Only use the blade rated at higher speed
than that of main unit.
The blade may be damaged if the blade is
used under the rated speed of the main unit.
Disengage the front cover lock button and
remove any dust that has become clogged in-side
the cover. If the cover is clogged, use a long
object such as a manual screwdriver to unclog it.
After doing so, close the front cover. [Fig.2]
If there is dust inside the dust case, disengage
the dust case lock button, detach the dust case,
and remove the dust. After doing so, reattach the
dust case. [Fig.3]
Installing Blade
Follow these steps:
1. Remove the battery pack from the tool.
2. Remove any cutting debris from blade area.
3. Use the retracting handle to retract (open)
the lower guard.
4. Install the blade as illustrated. [Fig.4]
Make sure that both the direction arrow on
the blade and the direction arrow on the
transparent guard point in the same direc-
tion.
5. Set the outer washer in place.
6. Insert the hex bolt.
- 14 -

Publicité

loading

Ce manuel est également adapté pour:

Ey45a2Ey45a2xmEy45a2xw