Konect PROX4 Manuel D'utilisation page 23

maximum value and start to decreasing then the charge current
will turn off and finish the charge. If the trigger voltage set too high, there is a possible danger of
over- charging .If the trigger voltage set too low, may stopcharging prematurely. Please refer to the
specification of the battery.
Temp Cut-off
ON 65°C 149°F
INC
DEC
Safety Timer
ON 300min
DEC INC
Capacity Cut-Off
ON 10000mAh
INC
DEC
Key Beep
Buzzer
INC
DEC
Input Power Low
Cut-Off 18.0V
DEC INC
INC
DEC
Load Factory Set
Enter
INC
DEC
Product Version
V1.1.1
decreasing then the charge current will turn o and nish
the charge. If the trigger voltage set too high, there is a
possible danger of over- charging .If the trigger voltage set
too low, may stopcharging prematurely. Please refer to the
speci cation of the battery (NiCd default voltage:12mv,
NiMH default voltage:7mv).
Temp cut-off program
Temp cut-off program
Temp cut-o
Temp cut-off program is used to protect charger being damaged. Will
damaged. Will trigger stop charge/discharge when in
trigger stop charge/discharge when in extreme or high temperature
extreme or high temperature environment. Temperature cut
environment. Temperature cut off value can set from 60° to 80°.
If you turn on safety timer, safety timer will start timing
o value can set from 60° to 80°.
Safety time setting
when charging.If system fault or system can't identify
Safety time setting
If you turn on safety timer, safety timer will start timing
battery capacity already full, this safety time set can stop
when charging.If system fault or system can't identify
If you turn on safety timer, safety timer will start timing when
battery being over charged. The safety time should not
charging.If system fault or system can't identify battery capacity
battery capacity already full, this safety time set can stop
shorter than the time battery fully charged, usually from
already full, this safety time set can stop battery being over charged.
battery being over charged. The safety time should not
10min to 720min.
The safety time should not shorter than the time battery fully charged,
shorter than the time battery fully charged, usually from
usually from 10min to 720min.
10min to 720min.
Capacity cut-off program
Capacity cut-o
Capacity cut-off program
capacity. If safety timer stopped work or system can't detect Capacity cut-o
Capacity cut-off program set the maximum charging capacity. If
the peak voltage, this program will stop charging/ discharg- capacity. If safety timer stopped work or system can't detect
safety timer stopped work or system can't detect the peak voltage,
ing automatically if you've set the maximum charging the peak voltage, this program will stop charging/ discharg-
this program will stop charging/ discharging automatically if you've
capacity, range from 10mAh to 50000mAh. .
ing automatically if you've set the maximum charging
set the maximum charging capacity, range from 10mAh to
50000mAh.
capacity, range from 10mAh to 50000mAh. .
ON Sound setting
Sound setting
ON
Beep sound on/off; Buzzer sound on/off.
Beep sound on/o ; Buzzer sound on/o .
DC input power is 19-26V, the program set the lowest cut-o
Input Power low cut-off
DC input power is 19-26V, the program set the lowest cut-o
input voltage value is 19-26V. If the voltage lower than the
DC input power is 19-26V, the program set the lowest cut-off input
input voltage value is 19-26V. If the voltage lower than the
setting voltage level, procedure will be forced to end to
voltage value is 19-26V. If the voltage lower than the setting voltage
setting voltage level, procedure will be forced to end to
level, procedure will be forced to end to protect input power. protect input power.
protect input power.
Load factory set
Load factory set
Load factory set
Resume to the default setting by pressing ENTER for more than 2 Resume to the default setting
seconds
Product version
This is used to check product version
program is used to protect charger being
program set the maximum charging
program set the maximum charging
23