Publicité
Les langues disponibles
Les langues disponibles
After choose the right channel, press ENTER key and through press DEC or INC key to
choose battery type, including LiPo、 LiFe、 Liion、 LiHV、 NiMH、 NiCD、 PB batteries. Or you
can start program setting, voltage test, data storage.
This LiHV mode can only support 4.35V Lithium battery, forbidden to use other
This LiHV mode can only support 4.35V Lithium battery, forbidden to use other batteries to
batteries to charge under this mode. Charge LiPo/LiIon/LiFe or other batteries
charge under this mode. Charge LiPo/LiIon/LiFe or other batteries voltage under 4.20V in
LiHV mode may cause possible fire or explosion.
voltage under 4.20V in LiHV mode may cause possible fire or explosion.
Press STOP key Back to the last interface, then press ENTER key to the next menu.
Press STOP key Back to the last interface, then press ENTER key to the next menu.
LiPo BALANCE
9.9A 14.8V(4S)
4S
0.4A 16.6V
CHG 001:01
00007
INC
DEC
1:4.14V 2:4.15V
3:4.14V 4:4.14V
9. CELL METER TEST PROGRAM
User Program
Cell Meter
Start
Enter
MAIN:16.79V
H:4.20V L:4.19V
Start
Enter
1:4.20V 2:4.19V
3:4.20V 4:4.20V
Warning
Choose the right program, press ENTER key to choose balance
Choose the right program, press ENTER key to choose
charging mode or fast charging mode enter into next program, back
balance charging mode or fast charging mode enter into
press STOP key.
next program, back press STOP key.
Shortly press ENTER key to current setting. Through press INC/DEC
key to set current, range from 0.1-10A, shortly press ENTER key
Shortly press ENTER key to current setting. Through press
again, then through press INC/DEC key to set battery counts:3.7V(1S)-
INC/DEC key to set current, range from 0.1-10A, shortly press
14.8V(4S). After finished, long press ENTER key to charging program.
ENTER key again, then through press INC/DEC key to set
Press STOP key back to last menu, then press ENTER key to start
battery counts:3.7V(1S)-14.8V(4S). After nished, long press
program.
ENTER key to charging program.
Press INC key to show each single cell battery.
Press STOP key back to last menu, then press ENTER key to
Press DEC key to show charge power, battery capacity and charger's
inner temperature.
start program.
Press STOP key and confirm exit to stop current program and back
Press INC key to show each single cell battery.
to last menu.
Press DEC key to show charge power, battery capacity and
charger's inner temperature..
Press STOP key and con rm exit to stop current program and
back to last menu.
This charger with built-in high-bit micro-processor, can be used as a
This charger with built-in high-bit micro-processor, can be
cell meter.It can show the voltage of each cells, the total battery pack
used as a cell meter.It can show the voltage of each cells, the
voltage and the highest/lowest voltage.
total battery pack voltage and the highest/lowest voltage.
Choose the cell meter program interface, press START to enter.
Choose the cell meter program interface, press START to
Press START key to show the highest/lowest voltage of the single cell
enter.
and the total voltage of the battery pack.
Press START to show 1-4 cells voltage. Press STOP key back to main
Press START key to show the highest/lowest voltage of the
menu.
single cell and the total voltage of the battery pack.
press START to show 1-4 cells voltage. Press STOP key back
to main menu.
21
Publicité
