DeWalt DW733 Traduction De La Notice D'instructions Originale page 19

HEAVY-DUTY PORTABLE THICKNESS PLANER
DW733
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
E
product development and innovation make D
reliable partners for professional power tool users.
Technical Data
Voltage
Type
Power input
No load speed
Operating / Resting time
Feed speed
Cutting height (max.)
Cutting width (min. – max.)
Max. cutting depth (for max. board width of 140 mm)
Weight
L (sound pressure)
PA
K (sound pressure uncertainty)
PA
L (sound power)
WA
K (sound power uncertainty)
WA
Fuses
Europe 230 V tools 16 Amperes, mains
NOTE: This device is intended for connection to a power supply system
with maximum permissible system impedance Zmax of 0.25 Ω at the
interface point (power service box) of user's supply.
The user has to ensure that this device is connected only to a power
system which fulfils the requirement above. If necessary, the user can
ask the public power supply company for the system impedance at the
interface point.
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
NOTICE: Indicates a practice not related to personal
injury which, if not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes sharp edges.
All manuals and user guides at all-guides.com
EC-Declaration of Conformity
MACHINERY DIRECTIVE
WALT one of the most
E
DW733
D
DW733
are in compliance with:
2006/42/EC; EN61029-1; EN61029-2-3.
V 230
DC
These products also comply with Directive 2004/108/EC. For more
2
information, please contact D
W 1.800
the back of the manual.
min 10,000
-1
The undersigned is responsible for compilation of the technical file and
min 1/3
makes this declaration on behalf of D
m/s 0.13
mm 152
mm 64 – 315
mm 3.2
kg 33
Horst Grossmann
Vice President Engineering and Product Development
dB(A) 95
D
dB(A) 3.3 D-65510, Idstein, Germany
01.03.2010
dB(A) 108
dB(A) 3.7
Safety Instructions
Read all these instructions before attempting to operate this product
and save these instructions.
General Safety Rules
WALT declares that these products described under "technical data"
E
WALT at the following address or refer to
E
WALT, Richard-Klinger-Straße 11,
E
WARNING! When using electric tools basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury
including the following.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250–300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g., in the
presence of flammable liquids and gases.
3. Guard against electric shock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g., high humidity, when metal swarf is being
produced, etc.), electric safety can be improved by inserting an
isolating transformer or a (FI) earth-leakage circuit-breaker.
4. Keep other persons away.
Do not let persons, especially children, not involved in the work,
touch the tool or the extension cord and keep them away from the
work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was
intended.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do
not use tools for purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
ENGLISH
WALT.
E
17