Publicité
12
| English
OPERATION
WARNING: Dry running for more than 2 minutes
can lead to damage of the high-pressure pump. If
the appliance does not build up pressure within
2 minutes, switch the appliance off and proceed
in accordance with the instructions in Chapter
"Troubleshooting"
High pressure operation
CAUTION: Keep a distance of at least 30 cm when
using the jet for cleaning painted surfaces to
avoid damage.
CAUTION: Make sure the ON/OFF switch is set to
"OFF" and insert the plug into a properly installed
socket.
ATTENTION: The washer must be used on a se-
cure and stable surface in a standing, upright posi-
tion. Connect the product to the power and water
supply as described.Open the water supply. Hold
the spray gun with both hands.Direct the nozzle
of the chosen accessory away from you towards
the surface to be cleaned.Unlock the trigger and
press it until a constant amount of water flows
through the nozzle, to allow air trapped in the
hose to escape.Release the trigger.
Turn "ON" the switch "ON/OFF".
Hold the spray gun with both hands. Direct the
water jet to the object to be cleaned and press
the trigger.
WARNING: Beware of kickback when pressing
the trigger!
The factory pre-set pressure provides the best
water pressure and cleaning effect. If the pres-
sure must be lowered down, it can be adjusted
followingthe below methods:
Gradually keep the surface to be cleaned further
away. The further the surface is, the lower the
pressure is applied.
OPERATION WITH DETERGENT
Detergent can only be added when the device is
operated in low pressure mode.
DANGER: When using detergents, the material
data safety sheet issued by the detergent man-
ufacturer must be viewed, especially the instruc-
tions regarding personal protective equipment.
Remove the cap of the clean detergent bottle.
Gently pull the onboard detergent tank out of its
storage position.
Fill the tank with detergent designed specifically
for use with pressure washers.
RECOMMENDED CLEANING METHOD
• Spray the detergent sparingly on the dry sur-
face and allow it to react, but not to dry.
• Spray off loosened dirt with the high pressure
Met.
AFTER THE OPERATION WITH DETERGENT
Remove the hose clean detergent bottle from
the intake and close it with the lid, then clean the
detergent injection system with clean water. To
achieve a complete cleaning job on the detergent
injection system, apply detergent hose on clean
water to make sprays until the remaining deter-
gent is cleaned out from the system. Factory of
the high pressure cleaner is not responsible for
the damage caused by detergent or any chemical
agent.
OPERATION WITH BREAKS
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
• Put the trigger gun with the spray lance into
the parking position.
• During longer breaks(more than 5 minutes),
also turn the appliance off using the "ON/OFF"
switch.
START
• Check inlet hose for residues and clogs
• Connect water supply and pump inlet with in-
let hose and make sure the hose is air tide.
• Connect high pressure hose to pump outlet.
• Turn on the water supply
• Start the electrical motor while turning ON
the "ON/OFF" switch
• Pull the spray gun trigger, starting to spray
• Release the trigger and stop the water
• Adjust spray pattern by changing nozzle.
STOP
• Release the lever of the trigger gun.
• Shut off water supply.
• Turn off the appliance "ON/OFF".
• Disconnect the mains plug from the socket.
• Press the lever of the trigger gun to release
any remaining pressure in the system.
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
ATTENTION
• When disconnecting the supply or high pres-
sure hose, warm water may leak from the con-
nection after operation.
FROST PROTECTION
WARNING
Appliance and accessories that are not completely
drained can be destroyed by frost.
Completely drain appliance and accessories in or-
der to protect them against frost.
To avoid damage:
• Detach the appliance from the water supply.
• Detach spray lance from the trigger gun.
• Turn on the appliance "ON/OFF".
• Push the lever of the trigger gun until no more
water is coming out.
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
• Turn off the appliance "ON/OFF".
• Store the appliance and the entire accessories
in a frost free room.
HPW 155i PRO
Publicité
