Table des Matières
Publicité
Custodia per telecamera ed accessori
Materiale: estruso e pressofusione di allumi-
nio
Verniciatura: polveri epossidiche RAL9002
Grado di protezione: IP66
Tettuccio
Dimensioni esterne:
113x71x330 mm
4,4x2,8x13 in
(220)
113x71x370 mm
4,4x2,8x14,6 in
(260)
113x71x410 mm
4,4x2,8x16,1 in
(300)
Peso: 0,3 Kg
(220)
0,4 Kg
(260)
0,5 Kg
(300)
Riscaldamento
Ingombro:
70x65x70 mm
2,8x2,6x2,8 in
Alimentazione:
12VDC-24VAC, 20W
115-230VAC, 40W
Temperatura ON: < 14°C +/- 3°C
< 39°F +/- 5°F
Temperatura OFF: > 20°C +/- 3°C
> 68°F +/- 5°F
Ventilatore
Ingombro:
70x65x70 mm
2,8x2,6x2,8 in
Alimentazione:
12VDC, 1W
24VAC, 4W
230VAC, 4W
Temperatura ON: > 35°C +/- 3°C
> 95°F +/- 5°F
Temperatura OFF: < 20°C +/- 3°C
< 68°F +/- 5°F
Alimentatore per telecamera
Ingombro:
70x65x90 mm
2,8x2,6x3,5 in
Tensione di ingresso: 230VAC o 115VAC
Tensione di uscita: 12VDC o 24VAC
Corrente fornita: 400mA
Tensione riscaldamento: tensione ingresso
Peso: 0,4 Kg
Supporti
Staffa a parete
Dimensioni:
70x115x285 mm
2,7x4,5x11,2 in
Peso: 0,6 Kg
Fissaggio a parete, lo snodo consente la
regolazione su due assi, portata 25 Kg.
Vedi figura 12.
Staffa a parete
Dimensioni:
75x115x285 mm
3x4,5x11,2 in
Peso: 0,6 Kg
Fissaggio a parete, lo snodo consente la
regolazione su due assi, portata 25 Kg.
Vedi figura 13.
Staffa a soffitto
Dimensioni:
ø 170x255x390 mm
ø 6,7x10x15,4 in
Peso: 1,4 Kg
Fissaggio a soffitto, lo snodo consente la
regolazione su due assi, portata 25 Kg.
Vedi figura 14.
Supporto a colonna
Dimensioni:
ø 110x235 mm
ø 4,3x9,3 in
Peso: 0,45 Kg
Fissaggio a colonna, lo snodo consente la
regolazione su due assi, portata 25 Kg.
Vedi figura 15.
4
ITALIANO
ENGLISH
INTRODUCTION
Medium weatherproof housing for general
use.
Its modern design and internal dimensions
make it suitable for most of the 1/3" and
1/4" cameras equipped with fixed-focus len-
ses or small zoom lenses available on the
market. The particular camera opening and
fixing systems make installation easier. This
housing guarantees a weatherproof stan-
dard IP66 and thanks to the wide range of
accessories available, such as heater kit,
blower kit, camera power supply, sunshield,
it allows both indoor and outdoor installa-
tions. It is equipped with two PG9 cable
glands for external connections and is avai-
lable in the 220, 260 and 300mm versions.
Turn off the power before performing
any operations.
Products and accessories
Body + sunshield + heater kit
Dustproof body only
Sunshield
Thermostatically controlled PTC heater kit
Pre-installed
thermostatically
blower kit
Thermostatically controlled blower kit moun-
ted at the back (for a future installation)
Camera power supply
Weatherproof junction box
Camera power supply in weatherproof box
INSTALLATION
How to open the housing
To open the housing, unscrew the two screws
placed on the side in the middle of the rear
cover plate (fig.1 point 1), take the body out
(point 2), hang it onto the suitable holder
(fig. 7 point 1) and leave the internal and
external slide in the working position.
Before closing the housing take off the pro-
tective nylon and put silicagel salts envelope
into.
Camera housing and accessories
How to install the camera
This chapter describes how to install the
camera into the housing. We wish to remind
our customers that power supply can be
drawn from the power supply or heating cir-
cuit, if available, after checking that the right
supply voltage is used.
1. Remove the body by unscrewing the
two screws placed on the rear cover
plate.
2. Move the internal slide sideways to
enter its lower part (fig. 3 point 1).
3. Put the insulating washer between the
1/4" screw and the lower part of the
slide, set the insulating spacer
between the camera and the upper
part of the slide (fig. 2 point 1), tigh-
ten the 1/4" screw and position the
camera wherever wished (fig. 2 point
2).
4. If necessary use the additional spa
cers for a proper positioning of the
camera and of the zoom lenses.
5. Re-set the slide in the working position
and close the housing.
How to install the heater kit
controlled
This chapter describes how to install the hea-
ter kit option in the dustproof housings that
are not equipped with it. The power input of
the heater kit can be 12-24VDC/VAC or
115-230VAC versions. We wish to remind
our customers that the heater kit option can
be mounted together with the blower kit only
if the power input of the latter is 12VDC or
24VAC.
1. Remove the body by unscrewing the
two screws on the rear cover plate.
2. Rotate the internal slide in order to
allow access to its lower part (fig. 3
point 1).
3. Fix the PTC element, by means of the
relevant plate, on the lowest part of
the internal slide (point 2). Let the
wires run along the guides (point 3)
and let them go through the relevant
hole (point 4).
5
Publicité
Table des Matières
