Table Des Matières; Symbols - Festool KAPEX Manuel D'utilisation Original

English
Contents
1 Symbols....................................................... 6
2 About this manual....................................... 7
3 Safety warnings...........................................7
4 Intended use..............................................11
5 Specifications............................................ 11
6 Parts of the machine.................................11
7 Operation................................................... 12
8 Settings......................................................14
9 Working with the power tool..................... 18
10 Service and maintenance..........................21
11 Accessories............................................... 24
12 Environment.............................................. 24
1

Symbols

Warning of general danger
Warning of electric shock
Read the operating instructions and
safety instructions.
Danger area! Keep hands away!
Wear protective goggles.
Wear a dust mask.
Wear ear protection.
Caution! Laser beams!
Wear protective gloves.
Do not dispose of it with domestic
waste.
Safety class II
Tip or advice
Handling instruction
Electronics with ajustable and constant
speed as well as temperature monitor­
ing
FastFix Tool replacement
6
Quick-acting brake for safe work
Wood
Laminated wooden panels
Eternit fibre cement panel
Aluminium
W watt
mm millimetre
" inch
rpm
revolutions per minute
min -1
A amperes
V volt
Hz hertz
n
no load speed
0
kg kilogram
lb. pound
° angular degree
AVERTISSEMENT
Portez une protection oculaire.
Veillez à ce que votre corps, notamment vos mains, soit
toujours en dehors de la trajectoire de la lame de scie. Tout
contact avec la lame provoque des blessures graves. Contrôlez
le système de protection pour vous assurer qu'il fonctionne
correctement. N'effectuez aucune opération à main levée.
N'approchez jamais vos mains de la lame de scie. Avant de
déplacer la pièce à usiner ou de modifier des réglages, mettez
l'appareil à l'arrêt et attendez jusqu'à ce que la lame de scie
soit complètement immobile.
WARNING wear eye protection. Keep hands
and body out of the path of the saw blade.
Contact with blade will result in serious in­
jury. Check guarding system to make sure it
is functioning correctly. Do not perform any
operation freehand. Never reach around saw
blade. Turn off tool and wait for saw blade to
stop before moving workpiece or changing
settings.
LASER RADIATION- DO NOT STARE INTO BEAM! LASER RADIATION- DO NOT STARE INTO BEAM!
LIGHT EMITTING DIODE CLASS 2: LIGHT EMITTING DIODE CLASS 2:
IEC 60825-1:2007 IEC 60825-1
P ≤ 1mW; 640nm ≤ λ ≤ 660nm P ≤ 1mW; 640nm ≤ λ ≤ 660nm
LASER BEAM do not look in the beam !Light
emitting diode class 2, EN 60825-1 P ≤ 1 mW;
640 nm ≤ λ ≤ 660 nm.
WARNING
Wear eye protection. Keep hands and body out of
the path of the saw blade. Contact with blade will result in serious
injury. Check guarding system to make sure it is functioning
correctly. Do not perform any operation freehand. Never reach
around saw blade. Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
ADVERTENCIA
Lleve protección ocular. Mantenga las
manos y las demás partes del cuerpo alejadas de la trayectoria de la
hoja de sierra. El contacto con la hoja ocasiona lesiones graves.
Compruebe el sistema de protección para asegurarse de que
funciona correctamente. No efectúe ninguna operación a mano
alzada. Nunca se acerque demasiado a la hoja de sierra ni la toque.
Desconecte la herramienta y espere a que la hoja se detenga antes
de desplazar la pieza de trabajo o de modificar los ajustes.